EUVIMEDEUVIMED entdecken
Randomisierte kontrollierte StudieOpen Access · CC BY 4.0

Advancing Conservative Treatment of Knee Osteoarthritis: 3D‐Printed Shoe Soles for Passive Toe‐Out Gait Modification

Ziang Jiang, Paciane Bo Studer, Matthias Zäh, Christian Kryenbühl, Stephan Reichenbach, William R Taylor iD, Qiang Zhang

Journal of Foot and Ankle Research · 2026-06 · 19 (2)

DOI: 10.1002/jfa2.70174 ↗

Kurz gefasst

Randomisierte kontrollierte Studie in der Zeitschrift Journal of Foot and Ankle Research, online erschienen am 22.06.2026. Verfasst von Ziang Jiang und 6 weiteren Autor:innen. Beteiligte Einrichtung: Institute for Biomechanics, ETH Zürich, Zürich, Switzerland. Hauptthemen laut MEDLINE: Shoes, Gait, Osteoarthritis, Knee, Printing, Three-Dimensional. Die Arbeit nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Innosuisse - Schweizerische Agentur für Innovationsförderung.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Introduction

To evaluate whether a 3D‐printed shoe sole can passively replicate toe‐out gait biomechanics and reduce the knee adduction moment (KAM) and knee adduction angular impulse (KAAI), addressing limitations of traditional gait retraining.

Methods

Custom shoe soles were 3D‐printed using gyroid infill structures to create a rotational hind‐sole and a variable stiffness fore‐sole (‘RVS’ shoes). Twenty‐one healthy adults completed three baseline gait trials in control shoes, followed by randomised biofeedback‐based gait retraining at toe‐out angles of 5°, 10° and 15°. After each retraining session, motion capture was used during overground walking. Participants then walked wearing RVS shoes for three trials. Gait biomechanics were analysed using repeated measures ANOVA and multiple linear regression.

Results

Compared to baseline, KAM's second peak was significantly reduced after toe‐out retraining: 5° (13.6%, p = 0.002), 10° (20.2%, p < 0.001) and 15° (31.7%, p < 0.001). RVS shoes alone reduced it by 16.3% ( p < 0.001), and KAAI by 8.6% ( p < 0.001)—a reduction not achieved by retraining. Regression analysis showed that changes in KAM were strongly predicted (95%) by knee centre‐of‐pressure offset and mediolateral ground reaction force.

Conclusion

3D‐printed RVS shoes passively replicated or exceeded the biomechanical effects of active toe‐out gait retraining, offering a promising, low‐effort intervention for managing knee osteoarthritis.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ShoesGaitOsteoarthritis, KneePrinting, Three-DimensionalConservative TreatmentHumansBiomechanical PhenomenaFemaleMaleAdultEquipment DesignBiofeedback, PsychologyRange of Motion, ArticularWalking

Stichwörter der Autor:innen

3D‐printed shoe solesfoot orthosisgait modificationjoint kineticsknee osteoarthritis

Autor:innen und Institutionen

  • Institute for Biomechanics, ETH Zürich, Zürich, Switzerland.
  • Swissbiomechanics AG, Einsiedeln, Switzerland.
  • Institute of Social and Preventive Medicine, University of Bern, Bern, Switzerland.
  • Department of Rheumatology and Immunology, Inselspital, Bern University Hospital, University of Bern, Bern, Switzerland.

ORCID-Profile: William R Taylor

Förderung

  • Innosuisse - Schweizerische Agentur für Innovationsförderung

Zitieren

APA

Jiang, Z., Studer, P. B., Zäh, M., Kryenbühl, C., Reichenbach, S., Taylor, W. R., & Zhang, Q. (2026). Advancing Conservative Treatment of Knee Osteoarthritis: 3D‐Printed Shoe Soles for Passive Toe‐Out Gait Modification. Journal of Foot and Ankle Research, 19(2). https://doi.org/10.1002/jfa2.70174

Vancouver

Jiang Z, Studer PB, Zäh M, Kryenbühl C, Reichenbach S, Taylor WR, et al. Advancing Conservative Treatment of Knee Osteoarthritis: 3D‐Printed Shoe Soles for Passive Toe‐Out Gait Modification. Journal of Foot and Ankle Research. 2026;19(2). doi:10.1002/jfa2.70174

BibTeX
@article{Jiang2026,
  author = {Jiang, Ziang and Studer, Paciane Bo and Zäh, Matthias and Kryenbühl, Christian and Reichenbach, Stephan and Taylor, William R and Zhang, Qiang},
  title = {Advancing Conservative Treatment of Knee Osteoarthritis: 3D‐Printed Shoe Soles for Passive Toe‐Out Gait Modification},
  journal = {Journal of Foot and Ankle Research},
  year = {2026},
  volume = {19},
  number = {2},
  doi = {10.1002/jfa2.70174}
}
Kostenlos starten →