EUVIMEDEUVIMED entdecken
Crossref

A preliminary study of the mechanical properties of 3D ‐printed personalized mesh titanium alloy prostheses and repair of hemi‐mandibular defect in dogs

Bingjing Zhao, Hong Wang, Changkui Liu, Huawei Liu, Xiaowen Zhao, Zenghui Sun, Min Hu iD

Journal of Biomedical Materials Research Part B: Applied Biomaterials · 2024

DOI: 10.1002/jbm.b.35466 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomedical Materials Research Part B: Applied Biomaterials, 2024. Verfasst von Bingjing Zhao und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Stomatology, The First Dongguan Affiliated Hospital of Guangdong Medical University, Dongguan, Guangdong, China. Hauptthemen laut MEDLINE: Titanium, Printing, Three-Dimensional, Alloys. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 31 Literaturangaben. Gefördert von: Talent Development Foundation of The First Dongguan Affiliated Hospital of Guangdong Medical University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study is a preliminary investigation exploring the mechanical properties of three‐dimensional (3D)‐printed personalized mesh titanium alloy prostheses and the feasibility of repairing hemi‐mandibular defects. The ANSYS 14.0 software and selective laser melting (SLM) were used to produce personalized mesh titanium alloy scaffolds. Scaffolds printed using different parameters underwent fatigue property tests and scanning electron microscopy (SEM) of the fracture points. Models of hemi‐mandibular defects (encompassing the temporomandibular joint) were created using beagle dogs. Freeze–dried allogeneic mandibles or 3D‐printed personalized mesh titanium alloy prostheses were used for repair. Gross observation, computed tomography (CT), SEM, and histological examinations were used to compare the two repair methods. The prostheses with filament diameters of 0.5 and 0.7 mm could withstand 14,000 times and >600,000 cycles of alternating stresses, respectively. The truss‐structure scaffold with a large aperture and large aperture ratio could withstand roughly 250,000 cycles of alternating forces. The allogeneic mandible graft required intraoperative shaping, while the 3D‐printed mesh titanium alloy prostheses were personalized and did not require intraoperative shaping. The articular disc on the non‐operated sides experienced degenerative changes. No liver and kidney toxicity was observed in the two groups of animals. The 3D‐printed mesh titanium alloy prostheses could effectively restore the shape of the mandibular defect region and reconstruct the temporomandibular joint.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

TitaniumPrinting, Three-DimensionalAlloysAnimalsDogsMandibleMaterials TestingSurgical MeshProstheses and Implants

Stichwörter der Autor:innen

3D printingbeagle dogsmandibular defectsmandibular reconstructiontitanium mesh

Substanzen

TitaniumAlloys

Autor:innen und Institutionen

  • Department of Stomatology, The First Dongguan Affiliated Hospital of Guangdong Medical University, Dongguan, Guangdong, China.
  • Scientific Research Platform, The Second Clinical Medical College, Guangdong Medical University, Dongguan, Guangdong, China.
  • Department of Stomatology, The Second Affiliated Stomatological Hospital of Jinzhou Medical University, Jinzhou, Liaoning, China.
  • Department of Oral and Maxillofacial Surgery, School of Stomatology, Xi'an Medical University, Shanxi, Xi'an, China.
  • Department of Stomatology, General Hospital of the PLA, Beijing, China.
  • Shenzhen Excellent Technology Research Institute, Shenzhen, Guangdong, China.

ORCID-Profile: Min Hu

Förderung

  • Talent Development Foundation of The First Dongguan Affiliated Hospital of Guangdong Medical University

Zitieren

APA

Zhao, B., Wang, H., Liu, C., Liu, H., Zhao, X., Sun, Z., & Hu, M. (2024). A preliminary study of the mechanical properties of 3D ‐printed personalized mesh titanium alloy prostheses and repair of hemi‐mandibular defect in dogs. Journal of Biomedical Materials Research Part B: Applied Biomaterials. https://doi.org/10.1002/jbm.b.35466

Vancouver

Zhao B, Wang H, Liu C, Liu H, Zhao X, Sun Z, et al. A preliminary study of the mechanical properties of 3D ‐printed personalized mesh titanium alloy prostheses and repair of hemi‐mandibular defect in dogs. Journal of Biomedical Materials Research Part B: Applied Biomaterials. 2024. doi:10.1002/jbm.b.35466

BibTeX
@article{Zhao2024,
  author = {Zhao, Bingjing and Wang, Hong and Liu, Changkui and Liu, Huawei and Zhao, Xiaowen and Sun, Zenghui and Hu, Min},
  title = {A preliminary study of the mechanical properties of 3D ‐printed personalized mesh titanium alloy prostheses and repair of hemi‐mandibular defect in dogs},
  journal = {Journal of Biomedical Materials Research Part B: Applied Biomaterials},
  year = {2024},
  doi = {10.1002/jbm.b.35466}
}
Kostenlos starten →