EUVIMEDPoznaj EUVIMED
Open access · CC BY 4.0

Modeling large‐scale bioreactors with diffusion equations. Part I: Predicting axial dispersion coefficient and mixing times

Pauli Losoi iD, Jukka Konttinen, Ville Santala

Biotechnology and Bioengineering · 2024-03 · 121 (3) · 1060-1075

DOI: 10.1002/bit.28632 ↗

At a glance

Journal article in Biotechnology and Bioengineering, published online on 2023-12-27. Written by Pauli Losoi and 2 co-authors. Institution: Faculty of Engineering and Natural Sciences, Tampere University, Tampere, Finland. Major MEDLINE topics: Bioreactors, Hydrodynamics. Cited 9 times so far (Crossref); 38 references. The full text is freely available (open access, CC BY 4.0). Funded by: Tampere University of Technology Graduate School, Novo Nordisk Foundation.

AbstraktSubjectsDane bibliograficzneCiteRelated studies

Abstract (original language)

Bioreactor scale‐up is complicated by dynamic interactions between mixing, reaction, mass transfer, and biological phenomena, the effects of which are usually predicted with simple correlations or case‐specific simulations. This two‐part study investigated whether axial diffusion equations could be used to calculate mixing times and to model and characterize large‐scale stirred bioreactors in a general and predictive manner without fitting the dispersion coefficient. In this first part, a resistances‐in‐series model analogous to basic heat transfer theory was developed to estimate the dispersion coefficient such that only available hydrodynamic numbers and literature data were needed in calculations. For model validation, over 800 previously published experimentally determined mixing times were predicted with the transient axial diffusion equation. The collected data covered reactor sizes up to 160 m 3 , single‐ and multi‐impeller configurations with diverse impeller types, aerated and non‐aerated operation in turbulent and transition flow regimes, and various mixing time quantification methods. The model performed excellently for typical multi‐impeller configurations as long as flooding conditions were avoided. Mixing times for single‐impeller and few nonstandard bioreactors were not predicted equally well. The transient diffusion equation together with the developed transfer resistance analogy proved to be a convenient and predictive model of mixing in typical large‐scale bioreactors.

Subjects

MeSH terms (MEDLINE)

BioreactorsHydrodynamics

Author keywords

axial dispersion coefficientbioreactordiffusion equationmixing timemodelingscale-up

Authors and institutions

  • Faculty of Engineering and Natural Sciences, Tampere University, Tampere, Finland.

ORCID profiles: Pauli Losoi

Funding

  • Tampere University of Technology Graduate School
  • Novo Nordisk Foundation

Cite

APA

Losoi, P., Konttinen, J., & Santala, V. (2024). Modeling large‐scale bioreactors with diffusion equations. Part I: Predicting axial dispersion coefficient and mixing times. Biotechnology and Bioengineering, 121(3), 1060-1075. https://doi.org/10.1002/bit.28632

Vancouver

Losoi P, Konttinen J, Santala V. Modeling large‐scale bioreactors with diffusion equations. Part I: Predicting axial dispersion coefficient and mixing times. Biotechnology and Bioengineering. 2024;121(3):1060-1075. doi:10.1002/bit.28632

BibTeX
@article{Losoi2024,
  author = {Losoi, Pauli and Konttinen, Jukka and Santala, Ville},
  title = {Modeling large‐scale bioreactors with diffusion equations. Part I: Predicting axial dispersion coefficient and mixing times},
  journal = {Biotechnology and Bioengineering},
  year = {2024},
  volume = {121},
  number = {3},
  pages = {1060--1075},
  doi = {10.1002/bit.28632}
}
Start for free →