Modeling large‐scale bioreactors with diffusion equations. Part I: Predicting axial dispersion coefficient and mixing times
Biotechnology and Bioengineering · 2024-03 · 121 (3) · 1060-1075
DOI: 10.1002/bit.28632 ↗Kurz gefasst
Fachartikel in der Zeitschrift Biotechnology and Bioengineering, online erschienen am 27.12.2023. Verfasst von Pauli Losoi und 2 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Engineering and Natural Sciences, Tampere University, Tampere, Finland. Hauptthemen laut MEDLINE: Bioreactors, Hydrodynamics. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Tampere University of Technology Graduate School, Novo Nordisk Foundation.
Abstract (Originalsprache)
Bioreactor scale‐up is complicated by dynamic interactions between mixing, reaction, mass transfer, and biological phenomena, the effects of which are usually predicted with simple correlations or case‐specific simulations. This two‐part study investigated whether axial diffusion equations could be used to calculate mixing times and to model and characterize large‐scale stirred bioreactors in a general and predictive manner without fitting the dispersion coefficient. In this first part, a resistances‐in‐series model analogous to basic heat transfer theory was developed to estimate the dispersion coefficient such that only available hydrodynamic numbers and literature data were needed in calculations. For model validation, over 800 previously published experimentally determined mixing times were predicted with the transient axial diffusion equation. The collected data covered reactor sizes up to 160 m 3 , single‐ and multi‐impeller configurations with diverse impeller types, aerated and non‐aerated operation in turbulent and transition flow regimes, and various mixing time quantification methods. The model performed excellently for typical multi‐impeller configurations as long as flooding conditions were avoided. Mixing times for single‐impeller and few nonstandard bioreactors were not predicted equally well. The transient diffusion equation together with the developed transfer resistance analogy proved to be a convenient and predictive model of mixing in typical large‐scale bioreactors.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Faculty of Engineering and Natural Sciences, Tampere University, Tampere, Finland.
ORCID-Profile: Pauli Losoi
Förderung
- Tampere University of Technology Graduate School
- Novo Nordisk Foundation
Zitieren
APA
Losoi, P., Konttinen, J., & Santala, V. (2024). Modeling large‐scale bioreactors with diffusion equations. Part I: Predicting axial dispersion coefficient and mixing times. Biotechnology and Bioengineering, 121(3), 1060-1075. https://doi.org/10.1002/bit.28632
Vancouver
Losoi P, Konttinen J, Santala V. Modeling large‐scale bioreactors with diffusion equations. Part I: Predicting axial dispersion coefficient and mixing times. Biotechnology and Bioengineering. 2024;121(3):1060-1075. doi:10.1002/bit.28632
BibTeX
@article{Losoi2024,
author = {Losoi, Pauli and Konttinen, Jukka and Santala, Ville},
title = {Modeling large‐scale bioreactors with diffusion equations. Part I: Predicting axial dispersion coefficient and mixing times},
journal = {Biotechnology and Bioengineering},
year = {2024},
volume = {121},
number = {3},
pages = {1060--1075},
doi = {10.1002/bit.28632}
}
EUVIMED