Investigation On the Bending Resistance of Double Layer Reinforced Concrete Beam Using River Gravel and Crush Granite
IOSR Journal of Mechanical and Civil Engineering · 2026-05 · 23 (5) · 13-31
DOI: 10.9790/1684-2305031331 ↗Kurz gefasst
Fachartikel in der Zeitschrift IOSR Journal of Mechanical and Civil Engineering, 2026-05. Verfasst von Wenapere A. D Wenapere A. D und 4 weiteren Autor:innen.
Abstract (Originalsprache)
This investigation focused on studying the bending capacity of double-layer reinforced concrete beam using river gravel and crushed granite. The primary objective is to determine the factors influencing the bending capacity of double-layer beams and analyze their behavior under different loading conditions. By understanding the factors influencing bending capacity, a prototype beam was design to enhance the overall strength and performance of the reinforced concrete beam. The production of this double layer RC beams. Ten (10) simply supported RC prototype beams (1000x75x112 mm) were subjected to laboratory study. Two 8 mm rebar in the tension zone and two 6mm diameter were provided as hanger bars 4mm diameter rebar spaced at 200 mm were used as shear bars and constructed for this research as specified EN1990, EN1991, EN1992. Preparation of the Beams, the concrete mix proportion used in preparing the concrete beams M15(1:2:4). The Reinforced concrete beam samples were grouped into six (6): the first group is made up of SCG as single layer of crushed granite 100%CG, the second group is made of SRG as single layer of river gravel 100%RG. The third group is made of double layer RC beams. These beams are identified as CG, RG for depth of top to bottom layer ratio 50CG/50RG, 50RG/50CG, 30RG/70CG and 70CG/30RG, respectively. The beam samples were subjected to a point load application to evaluate the load resistance and deflections were evaluated for their strength to support a load over a span of 900 mm after 28 days of curing. A dial gauge was positioned at the mid-span under the beam. The result showed that, the control beam for crushed granite SCG had ultimate failure load of 20.41kN with a corresponding deflection of 4.43 mm and bending capacity of 4.59 kNm the next inline was double layer beam, the compression layer (half depth of crushed granite) and the tension (half depth river gravel) 50%CG/50%RG, which failed at a load of 18.59 kN, with a corresponding deflection of 3.82 mm and a bending capacity of 4.65 kN the beam finally failed due to flexure. This beam is 9.03% less than the SCG. The double layer reinforced concrete beams had a similar load resistance as the reinforced concrete beams made entirely with SCG. Based on the experimental test result in the laboratory, it’s recommended that placing the weaker concrete (river gravel) in a double layer reinforced concrete beam at the tension zone enhance a desirable bending capacity which is similar to the control beam SCG.
Zitieren
APA
D, W. A. D. W. A., F, M. B. F. M. B., TrustGod, TrustGod, J. A., & A, J. (2026). Investigation On the Bending Resistance of Double Layer Reinforced Concrete Beam Using River Gravel and Crush Granite. IOSR Journal of Mechanical and Civil Engineering, 23(5), 13-31. https://doi.org/10.9790/1684-2305031331
Vancouver
D WADWA, F MBFMB, TrustGod, TrustGod JA, A J. Investigation On the Bending Resistance of Double Layer Reinforced Concrete Beam Using River Gravel and Crush Granite. IOSR Journal of Mechanical and Civil Engineering. 2026;23(5):13-31. doi:10.9790/1684-2305031331
BibTeX
@article{D2026,
author = {D, Wenapere A. D Wenapere A. and F, Micah B. F Micah B. and TrustGod and TrustGod, J. A and A, J.},
title = {Investigation On the Bending Resistance of Double Layer Reinforced Concrete Beam Using River Gravel and Crush Granite},
journal = {IOSR Journal of Mechanical and Civil Engineering},
year = {2026},
volume = {23},
number = {5},
pages = {13--31},
doi = {10.9790/1684-2305031331}
}
EUVIMED