EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Advanced superimposition method to evaluate the marginal and internal fit of ceramic crowns fabricated using heat pressing techniques

Nasser M Alqahtani, Saurabh Chaturvedi, Mohamed Khaled Addas, Manar Fahad A AlQahtani, Arwa Ahmed M Alhudiry, Shahrah H Qahtani, Mohammad A Zarbah, Asim Elsir Elmahdi, Marco Cicciù, Giuseppe Minervini

PeerJ · 2025

DOI: 10.7717/peerj.19117 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PeerJ, 2025. Verfasst von Nasser M Alqahtani und 9 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthetic Dentistry, College of Dentistry, King Khalid University, Abha, Aseer, Saudi Arabia. Hauptthemen laut MEDLINE: Crowns, Ceramics, Dental Prosthesis Design, Dental Marginal Adaptation. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 77 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: The Deanship of Scientific Research at King Khalid University through small group Research Project.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Background

Digital technologies can enhance the success of permanent crowns. The present study aimed to evaluate marginal adaptation and internal fit of permanent crowns fabricated using stereolithography (SLA) and digital light processing (DLP) 3D printing technologies following scans using two different intraoral scanners (IOS) (Medit i700, shape (TRIOS 3)).

Methods

Three typodont #14 teeth were prepared for full veneer all ceramic crowns with three types of margins—chamfer (CFL), rounded shoulder (RSFL) and rounded shoulder with bevel (RSBFL). A total of 360 study models were made and divided into two groups based on the type of intraoral scanner used for digital impressions. Group A in which the intraoral scanner MEDIT i700 was used, and Group B in which intraoral scanner TRIOS 3 was used (n = 360/group). The subgroups were made as Medit i700-SLA, Medit i700-DLP, TRIOS 3-SLA and TRIOS 3-DLP (n = 180/subgroup). These were further divided into three sub-subgroups based on the finish lines: CFL, RSFL, and RSBFL (n = 30 each sub-subgroups). All ceramic crowns were made on models and scanned to assess discrepancies (marginal adaptation and internal fit) at nine zones (Z1–Z9). Three-way analysis of variance and pairwise comparison was done (Tukey HSD test) ( α = 0.05).

Results

The mean marginal gap and internal fit values were lowest for Group A-1 with RSBFL in each zone. The intergroup comparison showed values for marginal gap and the internal fit were minimum for Group A-1 for each finish line design, with the lowest for RSBFL at zone Z2 0.04 ±0.001.

Conclusions

Regardless of the IOS and 3D printing techniques, the smallest gap was observed in RSBFL, followed by RSFL and CFL. The all-ceramic crowns fabricated using a Medit intraoral scanner with an SLA 3DPrinter with a rounded shoulder finish line had the best marginal and internal fit.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

CrownsCeramicsDental Prosthesis DesignDental Marginal AdaptationHumansComputer-Aided DesignPrinting, Three-Dimensional

Stichwörter der Autor:innen

3D PrintingAll-ceramic crownCAD-CAMDental softwareDigital dentistryIntra oral scanPermanent crown

Autor:innen und Institutionen

  • Department of Prosthetic Dentistry, College of Dentistry, King Khalid University, Abha, Aseer, Saudi Arabia.
  • Department of Biomedical and Surgical and Biomedical Sciences, Catania University, Catania, Italy.
  • Saveetha Dental College and Hospitals, Saveetha Institute of Medical and Technical Sciences (SIMATS), Saveetha University, Chennai, Tamil Nadu, India.
  • Multidisciplinary Department of Medical-Surgical and Dental Specialties, University of Campania Luigi Vanvitelli, Caserta, Italy.

Förderung

  • The Deanship of Scientific Research at King Khalid University through small group Research Project

Zitieren

APA

Alqahtani, N. M., Chaturvedi, S., Addas, M. K., AlQahtani, M. F. A., Alhudiry, A. A. M., Qahtani, S. H., Zarbah, M. A., Elmahdi, A. E., Cicciù, M., & Minervini, G. (2025). Advanced superimposition method to evaluate the marginal and internal fit of ceramic crowns fabricated using heat pressing techniques. PeerJ. https://doi.org/10.7717/peerj.19117

Vancouver

Alqahtani NM, Chaturvedi S, Addas MK, AlQahtani MFA, Alhudiry AAM, Qahtani SH, et al. Advanced superimposition method to evaluate the marginal and internal fit of ceramic crowns fabricated using heat pressing techniques. PeerJ. 2025. doi:10.7717/peerj.19117

BibTeX
@article{Alqahtani2025,
  author = {Alqahtani, Nasser M and Chaturvedi, Saurabh and Addas, Mohamed Khaled and AlQahtani, Manar Fahad A and Alhudiry, Arwa Ahmed M and Qahtani, Shahrah H and Zarbah, Mohammad A and Elmahdi, Asim Elsir and Cicciù, Marco and Minervini, Giuseppe},
  title = {Advanced superimposition method to evaluate the marginal and internal fit of ceramic crowns fabricated using heat pressing techniques},
  journal = {PeerJ},
  year = {2025},
  doi = {10.7717/peerj.19117}
}
Kostenlos starten →