EUVIMEDEUVIMED entdecken
Crossref

Effect of Filling Rate on Biodegradability in 3D Printed PCL-HA Scaffolds

Ahmet Fatih Kocaer, Rumeysa Hilal Çelik, Muhammet Bektaş

International Journal of Advances in Engineering and Pure Sciences · 20.03.2026 · 38 (1) · 23-37

DOI: 10.7240/jeps.1716692 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Journal of Advances in Engineering and Pure Sciences, online erschienen am 20.03.2026. Verfasst von Ahmet Fatih Kocaer und 2 weiteren Autor:innen. Die Arbeit nennt 26 Literaturangaben. Gefördert von: Çalışma için herhangi bir proje / Destek alınmamştır..

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In bone tissue engineering, scaffold architecture serves a dual function by providing mechanical support and regulating degradation behavior under physiological conditions. Polycaprolactone (PCL), a biodegradable and biocompatible polymer, is widely used in scaffold fabrication; however, due to its limited biological activity, it is often reinforced with bioactive ceramics such as hydroxyapatite (HA). PCL-HA composites offer both structural integrity and osteoconductive potential. While previous studies have investigated various parameters influencing scaffold performance, the specific role of infill density-an easily tunable parameter in fused deposition modeling (FDM)-on degradation kinetics remains underexplored. In this study, scaffolds composed of 90% PCL and 10% HA were fabricated with a tri-hexagon infill pattern, previously shown to enhance mechanical properties, especially in flexural and fatigue strength. The scaffolds were printed as flat plates (10×10×2 mm) and divided into ten experimental groups with infill densities ranging from 10% to 100%. All samples were incubated in Simulated Body Fluid (SBF) at 37 °C for 2, 4, and 8 weeks. Scaffold degradation was assessed by measuring mass loss and further characterized via SEM, EDX, and FTIR analyses. The results demonstrated that lower infill densities led to significantly faster degradation due to increased surface area exposure, resulting in more pronounced mass loss and surface erosion. SEM imaging confirmed morphological degradation, while EDX and FTIR analyses revealed chemical changes associated with polymer breakdown and partial dissolution of the HA phase. These findings highlight the critical role of infill density in modulating scaffold biodegradability and suggest that tri-hexagon patterned PCL-HA scaffolds offer a versatile design strategy for customized bone tissue engineering applications.

Förderung

  • Çalışma için herhangi bir proje / Destek alınmamştır.

Zitieren

APA

Kocaer, A. F., Çelik, R. H., & Bektaş, M. (2026). Effect of Filling Rate on Biodegradability in 3D Printed PCL-HA Scaffolds. International Journal of Advances in Engineering and Pure Sciences, 38(1), 23-37. https://doi.org/10.7240/jeps.1716692

Vancouver

Kocaer AF, Çelik RH, Bektaş M. Effect of Filling Rate on Biodegradability in 3D Printed PCL-HA Scaffolds. International Journal of Advances in Engineering and Pure Sciences. 2026;38(1):23-37. doi:10.7240/jeps.1716692

BibTeX
@article{Kocaer2026,
  author = {Kocaer, Ahmet Fatih and Çelik, Rumeysa Hilal and Bektaş, Muhammet},
  title = {Effect of Filling Rate on Biodegradability in 3D Printed PCL-HA Scaffolds},
  journal = {International Journal of Advances in Engineering and Pure Sciences},
  year = {2026},
  volume = {38},
  number = {1},
  pages = {23--37},
  doi = {10.7240/jeps.1716692}
}
Kostenlos starten →