EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-SA 4.0

Design, Kinematic Analysis, and Scaled Prototype Validation of a Pneumatic Ejection Mechanism for Supersonic Re-Entry Capsule Testing

Ahmad Samsul Arbai, Azzahra Nazwa Asyifa, Rajni Rizkia Sirat, Johnson Fernando, Rahmat Dani Sulistyo, Fajrul Falah

Multidisciplinary Innovations and Research in Applied Engineering · 30.06.2026 · 3 (1) · 1-12

DOI: 10.70935/k0qrps35 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Multidisciplinary Innovations and Research in Applied Engineering, online erschienen am 30.06.2026. Verfasst von Ahmad Samsul Arbai und 5 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-SA 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Lunar rover wheels must combine low mass, traction, compliance, abrasion resistance, and maintainability under vacuum, thermal cycling, and unconsolidated regolith. This study develops and evaluates an adaptive traction rover wheel for lunar surface mobility applications. The method combined requirement definition, terramechanics-based grouser sizing, material selection, CAD-based structural packaging, finite element evaluation, manufacturability assessment, and service-life estimation. The proposed wheel uses a two-piece Ti-6Al-4V rim, ten alternating compliant titanium spokes, ten 27 mm V-shaped grousers, a 6061-T6 aluminum hub, riveted mechanical joints, and Cr3C2-NiCr HVOF coating on soil-contact surfaces. The design achieved a diameter of 0.457 m, a width of 0.203 m, and a total mass of 2.254 kg. Linear-elastic structural screening indicated that the wheel supported a nominal normal load of 256 N with a factor of safety of approximately 2 based on a minimum Ti-6Al-4V yield-strength criterion of 828 MPa. The 3 g impact screening case produced a local peak von Mises stress of approximately 900 MPa, exceeding this conservative yield criterion and therefore requiring nonlinear analysis and experimental validation. Traction capability, wear resistance, and 1,000 km service-life estimates are analytical projections derived from geometry and wear modeling, not fully validated operational performance. The proposed architecture is therefore a lightweight, repairable, and traction-oriented wheel concept requiring targeted laboratory validation before mission use.

Zitieren

APA

Arbai, A. S., Asyifa, A. N., Sirat, R. R., Fernando, J., Sulistyo, R. D., & Falah, F. (2026). Design, Kinematic Analysis, and Scaled Prototype Validation of a Pneumatic Ejection Mechanism for Supersonic Re-Entry Capsule Testing. Multidisciplinary Innovations and Research in Applied Engineering, 3(1), 1-12. https://doi.org/10.70935/k0qrps35

Vancouver

Arbai AS, Asyifa AN, Sirat RR, Fernando J, Sulistyo RD, Falah F. Design, Kinematic Analysis, and Scaled Prototype Validation of a Pneumatic Ejection Mechanism for Supersonic Re-Entry Capsule Testing. Multidisciplinary Innovations and Research in Applied Engineering. 2026;3(1):1-12. doi:10.70935/k0qrps35

BibTeX
@article{Arbai2026,
  author = {Arbai, Ahmad Samsul and Asyifa, Azzahra Nazwa and Sirat, Rajni Rizkia and Fernando, Johnson and Sulistyo, Rahmat Dani and Falah, Fajrul},
  title = {Design, Kinematic Analysis, and Scaled Prototype Validation of a Pneumatic Ejection Mechanism for Supersonic Re-Entry Capsule Testing},
  journal = {Multidisciplinary Innovations and Research in Applied Engineering},
  year = {2026},
  volume = {3},
  number = {1},
  pages = {1--12},
  doi = {10.70935/k0qrps35}
}
Kostenlos starten →