EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Experimental Investigation of Solubility Trapping in 3D Printed Micromodels

Alexandros Patsoukis Dimou, Mahdi Mansouri Boroujeni, Sophie Roman, Hannah P. Menke, Julien Maes

InterPore Journal · 04.06.2025 · 2 (2) · IPJ040625-4

DOI: 10.69631/ipj.v2i2nr49 ↗

Kurz gefasst

Fachartikel in der Zeitschrift InterPore Journal, online erschienen am 04.06.2025. Verfasst von Alexandros Patsoukis Dimou und 4 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: EPSRC Centre for Doctoral Training in Additive Manufacturing, Agence Nationale de la Recherche, Ministère des Affaires Etrangères.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Understanding interfacial mass transfer during dissolution of gas in a liquid is vital for optimizing large-scale carbon capture and storage operations. While the dissolution of CO2 bubbles in reservoir brine is a crucial mechanism towards safe CO2 storage, it is a process that occurs at the pore-scale and is not yet fully understood. Direct numerical simulation (DNS) models describing this type of dissolution exist and have been validated with semi-analytical models on simple cases like a rising bubble in a liquid column. However, DNS models have not been experimentally validated for more complicated scenarios such as dissolution of trapped CO2 bubbles in pore geometries where there are few experimental datasets. In this work, we present an experimental and numerical study of trapping and dissolution of CO2 bubbles in 3D printed micromodel geometries. We used 3D printing technology to generate three different geometries, a single cavity geometry, a triple cavity geometry, and a multiple channel geometry. To investigate the repeatability of the trapping and dissolution experimental results, each geometry was printed three times, and three identical experiments were performed for each geometry. The experiments were performed at a low capillary number (Ca = 3.33 x 10-6), representative of flow during CO2 storage applications. The DNS simulations were then performed and compared with the experimental results. Our results show experimental reproducibility and consistency in terms of CO2 trapping and the CO2 dissolution process. At such a low capillary number, our numerical simulator cannot model the process accurately due to parasitic currents and the strong time-step constraints associated with capillary waves. However, we show that, for the single and triple cavity geometry, the interfacial transfer and resulting bubble dissolution can be reproduced by a numerical strategy where the interfacial tension is divided by 100 to relax the capillary time-step constraints. The full experimental dataset is provided and can be used to benchmark and improve future numerical models.

Förderung

  • EPSRC Centre for Doctoral Training in Additive Manufacturing
  • Agence Nationale de la Recherche
  • Ministère des Affaires Etrangères

Zitieren

APA

Dimou, A. P., Boroujeni, M. M., Roman, S., Menke, H. P., & Maes, J. (2025). Experimental Investigation of Solubility Trapping in 3D Printed Micromodels. InterPore Journal, 2(2), IPJ040625-4. https://doi.org/10.69631/ipj.v2i2nr49

Vancouver

Dimou AP, Boroujeni MM, Roman S, Menke HP, Maes J. Experimental Investigation of Solubility Trapping in 3D Printed Micromodels. InterPore Journal. 2025;2(2):IPJ040625-4. doi:10.69631/ipj.v2i2nr49

BibTeX
@article{Dimou2025,
  author = {Dimou, Alexandros Patsoukis and Boroujeni, Mahdi Mansouri and Roman, Sophie and Menke, Hannah P. and Maes, Julien},
  title = {Experimental Investigation of Solubility Trapping in 3D Printed Micromodels},
  journal = {InterPore Journal},
  year = {2025},
  volume = {2},
  number = {2},
  pages = {IPJ040625--4},
  doi = {10.69631/ipj.v2i2nr49}
}
Kostenlos starten →