EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

EFFECT OF FLAME-SPRAYING TEMPERATURE ON THE PROPERTIES OF Ni–Cr–B–Si-BASED SELF-FLUXING COATINGS

Dastan Buitkenov, Manarbek Kylyshkanov, Daryn Baizhan, Nurmahanbet Raisov, Nurkhat Bimakhan

Journal of Surface Engineering and Coating Technology · 2026

DOI: 10.66310/hoff2979 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Surface Engineering and Coating Technology, 2026. Verfasst von Dastan Buitkenov und 4 weiteren Autor:innen. Die Arbeit nennt 12 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Science and Higher Education of the Republic of Kazakhstan.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The present study investigates the effect of flame-spraying process parameters on the microstructure and mechanical properties of Ni–Cr–B–Si-based self-fluxing coatings. Corrosion-resistant AISI 321 austenitic chromium–nickel steel was used as the substrate material. The coatings were deposited by flame spraying using a Metal Coat 6PM-II system. To vary the thermal conditions of the spraying process, the oxygen-to-acetylene (O₂/C₂H₂) ratio was adjusted to 1.0, 1.1, and 1.2. The spraying parameters were monitored using an Accuraspray 4.0 diagnostic system. The resulting coatings were characterized in terms of microstructure, porosity, microhardness, surface roughness, and adhesion strength. Increasing the O₂/C₂H₂ ratio resulted in densification of the coating structure and a decrease in porosity from 1.97 ± 0.13% to 0.90 ± 0.09%. Concurrently, the surface roughness decreased from 4.70 ± 0.09 μm to 2.99 ± 0.11 μm, while the adhesion strength increased from 22.14 ± 4.3 MPa to 35.02 ± 3.9 MPa. The highest average microhardness of 1051.7 HV was obtained at an O₂/C₂H₂ ratio of 1.1. Among the investigated spraying conditions, the coating produced at O₂/C₂H₂ = 1.2 exhibited the lowest porosity and surface roughness together with the highest adhesion strength. The results demonstrate that controlling the O₂/C₂H₂ ratio provides an effective means of tailoring the microstructural and mechanical characteristics of flame-sprayed Ni–Cr–B–Si-based self-fluxing coatings.

Förderung

  • Ministry of Science and Higher Education of the Republic of Kazakhstan

Zitieren

APA

Buitkenov, D., Kylyshkanov, M., Baizhan, D., Raisov, N., & Bimakhan, N. (2026). EFFECT OF FLAME-SPRAYING TEMPERATURE ON THE PROPERTIES OF Ni–Cr–B–Si-BASED SELF-FLUXING COATINGS. Journal of Surface Engineering and Coating Technology. https://doi.org/10.66310/hoff2979

Vancouver

Buitkenov D, Kylyshkanov M, Baizhan D, Raisov N, Bimakhan N. EFFECT OF FLAME-SPRAYING TEMPERATURE ON THE PROPERTIES OF Ni–Cr–B–Si-BASED SELF-FLUXING COATINGS. Journal of Surface Engineering and Coating Technology. 2026. doi:10.66310/hoff2979

BibTeX
@article{Buitkenov2026,
  author = {Buitkenov, Dastan and Kylyshkanov, Manarbek and Baizhan, Daryn and Raisov, Nurmahanbet and Bimakhan, Nurkhat},
  title = {EFFECT OF FLAME-SPRAYING TEMPERATURE ON THE PROPERTIES OF Ni–Cr–B–Si-BASED SELF-FLUXING COATINGS},
  journal = {Journal of Surface Engineering and Coating Technology},
  year = {2026},
  doi = {10.66310/hoff2979}
}
Kostenlos starten →