EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Comparison of Force Delivery Profiles Between Thermoformed Aligners and Direct Printed Aligners During Canine Rotation: An In vitro Study

Mahalakshmi Krishnakumaran, Roshini T., Parameswaran T.M., Balaji Krishnan, Deepak Prabhu

Trends in Biomaterials and Artificial Organs · 30.07.2026 · 40 (3) · 231-236

DOI: 10.65795/vkxn9g80 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Trends in Biomaterials and Artificial Organs, online erschienen am 30.07.2026. Verfasst von Mahalakshmi Krishnakumaran und 4 weiteren Autor:innen. Die Arbeit nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Clear aligner therapy has become increasingly popular owing to its aesthetic and functional benefits; however, the force delivery characteristics of various aligner materials are not well understood. The advent of direct 3D-printed aligners has necessitated their comparison with traditional thermoformed materials. This study aimed to evaluate the force delivery of thermoformed (Zendura Viva) and direct 3D-printed (TA28) clear aligners during 1° and 2° rotational tooth movements, both before and after artificial aging. A total of 24 aligners were produced and categorized into two primary groups based on the material: thermoformed (Zendura Viva) and direct 3D-printed (TA28). Each group was further divided into subgroups for 1° and 2° rotational activation (n = 6 per subgroup). Force measurements were obtained using an FSR402 sensor integrated with an Arduino-based system under standardized conditions before (T0) and after artificial aging (T1), which involved thermocycling and incubation in artificial saliva. The initial force values of the thermoformed aligners were significantly higher than those of the direct 3D-printed aligners (p < 0.001). Artificial aging led to a notable reduction in force for both materials across all groups (P < 0.001). The three-way ANOVA revealed significant effects of material and aging, as well as a significant interaction between material and aging (p < 0.001), whereas the degree of rotation did not have a significant independent effect (p > 0.05). After aging, no statistically significant differences were observed between the materials. Thermoformed aligners provide higher initial forces; however, both thermoformed and direct 3D-printed aligners experience significant force degradation after aging, resulting in similar residual force levels. The degree of rotational activation has a limited impact on the long-term force delivery. These findings underscore the importance of material selection and force sustainability in optimizing orthodontic treatment using clear aligners.

Zitieren

APA

Krishnakumaran, M., T., R., T.M., P., Krishnan, B., & Prabhu, D. (2026). Comparison of Force Delivery Profiles Between Thermoformed Aligners and Direct Printed Aligners During Canine Rotation: An In vitro Study. Trends in Biomaterials and Artificial Organs, 40(3), 231-236. https://doi.org/10.65795/vkxn9g80

Vancouver

Krishnakumaran M, T. R, T.M. P, Krishnan B, Prabhu D. Comparison of Force Delivery Profiles Between Thermoformed Aligners and Direct Printed Aligners During Canine Rotation: An In vitro Study. Trends in Biomaterials and Artificial Organs. 2026;40(3):231-236. doi:10.65795/vkxn9g80

BibTeX
@article{Krishnakumaran2026,
  author = {Krishnakumaran, Mahalakshmi and T., Roshini and T.M., Parameswaran and Krishnan, Balaji and Prabhu, Deepak},
  title = {Comparison of Force Delivery Profiles Between Thermoformed Aligners and Direct Printed Aligners During Canine Rotation: An In vitro Study},
  journal = {Trends in Biomaterials and Artificial Organs},
  year = {2026},
  volume = {40},
  number = {3},
  pages = {231--236},
  doi = {10.65795/vkxn9g80}
}
Kostenlos starten →