EUVIMEDPoznaj EUVIMED
Open access · CC BY-NC-ND 4.0

SMART DUST BIN BASED ON ULTRASONIC SENSOR AND ARDUINO

N. Sreevally, P. Thanusri, A Dinesh Reddy, R. Akash, SK. Abdhul Moiz

International Journal of AI Electrical Civil and Mechanical engineering · 2026-11-17 · 2 (4) · 217-224

DOI: 10.64751/6bxes908 ↗

At a glance

Journal article in International Journal of AI Electrical Civil and Mechanical engineering, published online on 2026-11-17. Written by N. Sreevally and 4 co-authors. The full text is freely available (open access, CC BY-NC-ND 4.0).

AbstraktDane bibliograficzneCiteRelated studies

Abstract (original language)

Waste collection in towns and campuses is usually organised on a fixed route and a fixed schedule, without any knowledge of how full each bin actually is. As a result, some bins overflow and spread litter and odour around them, while others are emptied when they are nearly empty, wasting fuel and labour. Public bins also require people to touch a dirty lid, which discourages their use and spreads germs. This paper presents a smart dust bin based on an ultrasonic sensor and an Arduino UNO that opens its lid without contact, measures its own fill level, and reports that level to a cloud dashboard so that collection can be planned on actual need. The bin uses two HC-SR04 ultrasonic sensors. One sensor faces outward at the front of the bin and detects a hand or object within about 25 cm, after which the Arduino drives an SG90 servo motor to lift the lid and closes it again after a short delay. The second sensor is mounted under the lid facing down into the bin and measures the distance to the top of the waste. From the known depth of the bin, the controller converts this distance into a fill percentage, which is shown on a small LCD and indicated through green, yellow, and red LEDs. Connectivity is provided by an ESP-01 Wi-Fi module connected to the Arduino through a serial link, with an optional SIM800L GSM module for locations without Wi-Fi coverage. Every few minutes, and immediately when the fill level crosses 80 percent, the bin sends its identity, fill level, and battery voltage to a cloud platform. The dashboard lists all bins with their fill status and location, and a notification is sent to the collection supervisor when a bin needs to be emptied. Particular attention was given to the electrical design, since a bin in a public place must run for long periods on its own supply. The servo motor draws a high current pulse of several hundred milliamperes when it starts, so it is supplied from a separate regulated rail with a bulk capacitor to avoid resets of the controller. The system is powered by a 7.4 V lithium ion pack that can be charged from a small solar panel through a charge controller, and the Arduino places the ultrasonic sensors and Wi-Fi module in low power states between readings to extend battery life. A prototype built on a 30 litre bin was tested with different types of waste. The fill level measurement was accurate to within about 1.5 cm for solid waste with a reasonably flat surface, and the lid opened within 0.4 s of a hand being detected. The average current draw of about 38 mA gave an estimated battery life of more than five days without sunlight. Future work includes weight sensing, odour detection with a gas sensor, route optimisation for collection vehicles, and separation of wet and dry waste.

Cite

APA

Sreevally, N., Thanusri, P., Reddy, A. D., Akash, R., & Moiz, S. A. (2026). SMART DUST BIN BASED ON ULTRASONIC SENSOR AND ARDUINO. International Journal of AI Electrical Civil and Mechanical engineering, 2(4), 217-224. https://doi.org/10.64751/6bxes908

Vancouver

Sreevally N, Thanusri P, Reddy AD, Akash R, Moiz SA. SMART DUST BIN BASED ON ULTRASONIC SENSOR AND ARDUINO. International Journal of AI Electrical Civil and Mechanical engineering. 2026;2(4):217-224. doi:10.64751/6bxes908

BibTeX
@article{Sreevally2026,
  author = {Sreevally, N. and Thanusri, P. and Reddy, A Dinesh and Akash, R. and Moiz, SK. Abdhul},
  title = {SMART DUST BIN BASED ON ULTRASONIC SENSOR AND ARDUINO},
  journal = {International Journal of AI Electrical Civil and Mechanical engineering},
  year = {2026},
  volume = {2},
  number = {4},
  pages = {217--224},
  doi = {10.64751/6bxes908}
}
Start for free →