Passive flow control of Mach 4 mixed-compression intake using chevron grooves
FME Transactions · 2026 · 54 (1) · 53-69
DOI: 10.5937/fme2601053g ↗Kurz gefasst
Fachartikel in der Zeitschrift FME Transactions, 2026. Verfasst von Yash Gujar und 6 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Authors are thankful to Amity University Uttar Pradesh for providing their support in conducting the research work.
Abstract (Originalsprache)
Efficient operation of supersonic intakes is frequently hindered by shock-boundary layer interaction (SBLI), which induces large separation bubbles, pressure losses, and non-uniform flow at the engine face. To address these challenges, this work introduces Chevron Groove Modifications (CGM) as a novel passive flow-control strategy. A two-dimensional Mach 4 mixed-compression intake was modeled, and three groove configurations, downward, mid-surface, and upward were implemented on the ramp surface near the shock foot. High-resolution Reynolds-Averaged Navier-Stokes (RANS) simulations with the k-ω SST model were performed to assess the effects on separation factor (SF), total pressure recovery (TPR), and distortion coefficient (DC). Results indicate that upward chevron grooves (Case U-1) provided the most effective control, collapsing the throat separation bubble by approximately 83%, reducing distortion by ~30%, and enhancing TPR compared to the baseline case. Further parametric studies on groove depth and frequency revealed that shallow, high-frequency grooves (Case U-1B: 1 mm depth, frequency = 8) achieved the best balance, yielding smooth pressure distributions, low SF values, and distortion reduced to 38.8%. These improvements are attributed to the generation of strong counter-rotating vortices, which re-energize the boundary layer and weaken adverse shock interactions. Additional three-dimensional simulations confirm the reliability of the 2D predictions and capture spanwise effects. Off-design analyses across Mach 2.5-4.0 demonstrate that CGM enhances intake robustness, maintaining stable supersonic flow while imposing negligible drag penalties. These findings establish chevron grooves as an effective, geometry-based passive control technique to improve stability, pressure recovery, and operability in high-speed air-breathing propulsion systems.
Förderung
- Authors are thankful to Amity University Uttar Pradesh for providing their support in conducting the research work
Zitieren
APA
Gujar, Y., Tyagi, S., Mehboob, A., Singh, N., Saluja, R., Naagar, M., & Gahlot, N. (2026). Passive flow control of Mach 4 mixed-compression intake using chevron grooves. FME Transactions, 54(1), 53-69. https://doi.org/10.5937/fme2601053g
Vancouver
Gujar Y, Tyagi S, Mehboob A, Singh N, Saluja R, Naagar M, et al. Passive flow control of Mach 4 mixed-compression intake using chevron grooves. FME Transactions. 2026;54(1):53-69. doi:10.5937/fme2601053g
BibTeX
@article{Gujar2026,
author = {Gujar, Yash and Tyagi, Srishti and Mehboob, Aafrin and Singh, Narender and Saluja, Rajesh and Naagar, Manish and Gahlot, Neeraj},
title = {Passive flow control of Mach 4 mixed-compression intake using chevron grooves},
journal = {FME Transactions},
year = {2026},
volume = {54},
number = {1},
pages = {53--69},
doi = {10.5937/fme2601053g}
}
EUVIMED