EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Direct Ink Writing–Based Fabrication and Evaluation of Customized High-Density Surface Electromyography Electrode Arrays for Hand Gesture Classification

Ui-In Lee, Taeha Kim, Hyeju Roh, Junghun Sung, Woongki Hong, Hongki Kang

Journal of Flexible and Printed Electronics · 2026-06 · 5 (1) · 119-134

DOI: 10.56767/jfpe.250025 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Flexible and Printed Electronics, online erschienen am 30.06.2026. Verfasst von Ui-In Lee und 5 weiteren Autor:innen. Die Arbeit nennt 17 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: Samsung Research Funding & Incubation Center of Samsung Electronics.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

High-density surface electromyography (HD-sEMG) is increasingly important for wearable hand-gesture recognition and human–machine interface (HMI) applications. However, commercial wet electrodes still require conductive creams and adhesive foams, which can cause impedance instability, skin irritation, and hygiene issues during long-term use, limiting wearable practicality. Here, we developed a gel-free 36-channel stretchable HD-sEMG electrode using a Direct Ink Writing (DIW) process and validated its printing precision, electrical/mechanical stability, and machine-learning-based gesture classification performance. Ag interconnects and dome-shaped Ag/AgCl electrodes were printed on a TPU substrate and encapsulated with PDMS. Process optimization achieved a line width of 217±9.01 µm and a dome height of 569.3±19.9 µm at a 4 mm pitch, close to the target dimensions. Based on area-normalized impedance (|Z|·A), the printed electrode showed lower impedance than a commercial electrode across the measured frequency range. During a 6-hour wear test, repeated EIS measurements showed that the 1 kHz impedance stabilized from 1.66 MΩ to 0.95–1.02 MΩ, while the coefficient of variation remained around 1% at most time points. Under 30% strain for 1,000 tensile cycles, the electrode maintained electrical continuity and mechanical stability. In forearm HD-sEMG experiments, the electrode achieved SNRs of 17.06–21.34 dB (30% MVC) and 26.07–26.26 dB (100% MVC), and CNN and CNN–ViT models classified eight hand gestures with accuracies of 91.1% and 92.2%, respectively. These results demonstrate that the DIW-based gel-free electrodes can reliably acquire multi-channel muscle signals and suggest that muscle-informed channel grouping can be utilized in machine-learning frameworks for gesture applications.

Förderung

  • Samsung Research Funding & Incubation Center of Samsung Electronics

Zitieren

APA

Lee, U., Kim, T., Roh, H., Sung, J., Hong, W., & Kang, H. (2026). Direct Ink Writing–Based Fabrication and Evaluation of Customized High-Density Surface Electromyography Electrode Arrays for Hand Gesture Classification. Journal of Flexible and Printed Electronics, 5(1), 119-134. https://doi.org/10.56767/jfpe.250025

Vancouver

Lee U, Kim T, Roh H, Sung J, Hong W, Kang H. Direct Ink Writing–Based Fabrication and Evaluation of Customized High-Density Surface Electromyography Electrode Arrays for Hand Gesture Classification. Journal of Flexible and Printed Electronics. 2026;5(1):119-134. doi:10.56767/jfpe.250025

BibTeX
@article{Lee2026,
  author = {Lee, Ui-In and Kim, Taeha and Roh, Hyeju and Sung, Junghun and Hong, Woongki and Kang, Hongki},
  title = {Direct Ink Writing–Based Fabrication and Evaluation of Customized High-Density Surface Electromyography Electrode Arrays for Hand Gesture Classification},
  journal = {Journal of Flexible and Printed Electronics},
  year = {2026},
  volume = {5},
  number = {1},
  pages = {119--134},
  doi = {10.56767/jfpe.250025}
}
Kostenlos starten →