Optimization of Wire-EDM Parameters for the Enhanced Fabrication of Micro-Fin Arrays
Engineering, Technology & Applied Science Research · 11.08.2026 · 16 (4) · 38485-38491
DOI: 10.48084/etasr.19187 ↗Kurz gefasst
Fachartikel in der Zeitschrift Engineering, Technology & Applied Science Research, online erschienen am 11.08.2026. Verfasst von Ambi Rachel Alex und 4 weiteren Autor:innen. Die Arbeit nennt 20 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
Micro-pin fin arrays are significant components in compact heat transfer systems for advanced electronic cooling, where the demand for efficient, scalable, and cost-effective fabrication methods continues to grow. Conventional techniques, such as Lithography, Electroforming, and Molding (LIGA) and micro-Electrical Discharge Machining (micro-EDM), although precise, are complex, expensive, and require specialized infrastructure. The use of conventional 2-axis Wire Electrical Discharge Machining (Wire-EDM) to fabricate micro-pin fin arrays remains limited, particularly in balancing machining efficiency and dimensional accuracy. This study presents a straightforward and practical method for producing square micro-pin fin arrays on copper using a 2-axis Wire-EDM process, with a focus on optimizing key machining parameters. A 25 × 25 array of micro-fins was fabricated on copper square rods by systematically varying Pulse-on Time (PonT), Pulse-off Time (PoffT), Peak Current (I), and Table Speed (TS), employing a Taguchi L16 orthogonal array. Material Removal Rate (MRR) and Overcut (OC) were used as performance metrics, and significant factors were identified using Analysis of Variance (ANOVA). A multi-objective optimization strategy based on an Overall Evaluation Criterion (OEC) was used to determine the optimal machining conditions, and surface morphology was examined using Scanning Electron Microscopy (SEM). The results indicate successful fabrication of micro-fins with an average height of 850 µm and high dimensional accuracy. I and PonT emerged as the most influential parameters affecting both MRR and OC. The optimal conditions (PonT = 5 µs, PoffT = 15 µs, I = 4 A, TS = 60 µm/s) provided a balanced improvement in productivity and precision, with a prediction error below 5.60%. This study demonstrates a cost-effective and accessible alternative for micro-fin fabrication using conventional Wire-EDM and introduces a robust multi-objective optimization framework for microscale manufacturing.
Zitieren
APA
Alex, A. R., Vijayakumar, R., Jayakumar, S., Munusamy, R., & Tony, B. J. A. R. (2026). Optimization of Wire-EDM Parameters for the Enhanced Fabrication of Micro-Fin Arrays. Engineering, Technology & Applied Science Research, 16(4), 38485-38491. https://doi.org/10.48084/etasr.19187
Vancouver
Alex AR, Vijayakumar R, Jayakumar S, Munusamy R, Tony BJAR. Optimization of Wire-EDM Parameters for the Enhanced Fabrication of Micro-Fin Arrays. Engineering, Technology & Applied Science Research. 2026;16(4):38485-38491. doi:10.48084/etasr.19187
BibTeX
@article{Alex2026,
author = {Alex, Ambi Rachel and Vijayakumar, R. and Jayakumar, Sandhya and Munusamy, Rajesh and Tony, B. Jain A. R.},
title = {Optimization of Wire-EDM Parameters for the Enhanced Fabrication of Micro-Fin Arrays},
journal = {Engineering, Technology & Applied Science Research},
year = {2026},
volume = {16},
number = {4},
pages = {38485--38491},
doi = {10.48084/etasr.19187}
}
EUVIMED