EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Taguchi optimization of Wire EDM process parameters for machining LM5 aluminium alloy

Sunder Jebarose Juliyana, Jayavelu Udaya Prakash iD, Robert Čep iD, Charles Sarla Rubi, Sachin Salunkhe iD, Arasumugam Divya Sadhana, Emad Abouel Nasr

PLOS ONE · 28.10.2024 · 19 (10) · e0308203

DOI: 10.1371/journal.pone.0308203 ↗

Kurz gefasst

Fachartikel in der Zeitschrift PLOS ONE, online erschienen am 28.10.2024. Verfasst von Sunder Jebarose Juliyana und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, Vel Tech Rangarajan Dr. Sagunthala R&D Institute of Science and Technology, Avadi, Chennai, India. Hauptthemen laut MEDLINE: Alloys, Aluminum, Surface Properties. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 58 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: King Saud University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

LM5 alloy is suitable for metal castings for marine and aesthetic uses due to its admirable resistance to corrosion. In order to make intricate shapes in the LM5 alloy, this study intends to assess the impact of Wire Electric Discharge Machining process variables, like Pulse on Time (T on ), Pulse off Time (T off ), Gap Voltage (GV) and Wire Feed (WF) on responses like Material Removal Rate (MRR), Surface Roughness (SR), and Kerf Width (K w ). The LM5 aluminium alloy plate was produced through stir casting process. SEM, EDAX and XRD images confirm the LM5 Al alloy’s microstructure and crystal structure. WEDM studies were conducted using design of experiments approach based on L 9 orthogonal array and analysed using Taguchi’s Signal to Noise Ratio (S/N) analysis. Pulse on Time has the greatest statistical effects on MRR (68.25%), SR (79.46%) and kerf (81.97%). In order to assess the surface integrity of the WEDM machined surfaces, the SEM study on the topography was conducted using the optimum surface roughness process variables: T on 110 μs, T off 50 μs, GV 40 V, and WF 9 m/min. SEM images show the recast layer and its thickness. The average absolute error for MRR is 1.69%, SR is 3.89% and kerf is 0.88%, based on mathematical (linear regression) models. The Taguchi’s Signal to Noise ratio analysis is the most appropriate for single objective optimization of responses.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

AlloysAluminumSurface PropertiesMicroscopy, Electron, ScanningMaterials Testing

Substanzen

AlloysAluminum

Autor:innen und Institutionen

  • Department of Mechanical Engineering, Vel Tech Rangarajan Dr. Sagunthala R&D Institute of Science and Technology, Avadi, Chennai, India.
  • Department of Machining, Assembly and Engineering Metrology, Faculty of Mechanical Engineering, VSB-Technical University of Ostrava, Listopadu Ostrava, Czech Republic.
  • Department of Physics, Vel Tech Rangarajan Dr. Sagunthala R&D Institute of Science and Technology, Avadi, Chennai, India.
  • Department of Biosciences, Saveetha School of Engineering, Saveetha Institute of Medical and Technical Sciences, Chennai, India.
  • Department of Mechanical Engineering, Gazi University Faculty of Engineering, Maltepe, Ankara, Turkey.
  • Department of Industrial Engineering, College of Engineering, King Saud University, Riyadh, Saudi Arabia.

ORCID-Profile: Jayavelu Udaya Prakash, Robert Čep, Sachin Salunkhe

Förderung

  • King Saud University

Zitieren

APA

Juliyana, S. J., Prakash, J. U., Čep, R., Rubi, C. S., Salunkhe, S., Sadhana, A. D., & Nasr, E. A. (2024). Taguchi optimization of Wire EDM process parameters for machining LM5 aluminium alloy. PLOS ONE, 19(10), e0308203. https://doi.org/10.1371/journal.pone.0308203

Vancouver

Juliyana SJ, Prakash JU, Čep R, Rubi CS, Salunkhe S, Sadhana AD, et al. Taguchi optimization of Wire EDM process parameters for machining LM5 aluminium alloy. PLOS ONE. 2024;19(10):e0308203. doi:10.1371/journal.pone.0308203

BibTeX
@article{Juliyana2024,
  author = {Juliyana, Sunder Jebarose and Prakash, Jayavelu Udaya and Čep, Robert and Rubi, Charles Sarla and Salunkhe, Sachin and Sadhana, Arasumugam Divya and Nasr, Emad Abouel},
  title = {Taguchi optimization of Wire EDM process parameters for machining LM5 aluminium alloy},
  journal = {PLOS ONE},
  year = {2024},
  volume = {19},
  number = {10},
  pages = {e0308203},
  doi = {10.1371/journal.pone.0308203}
}
Kostenlos starten →