EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-SA 4.0

Evaluation of optical, surface, and microbiological properties of computer-aided design/computer-aided manufacturing-milled and three-dimensional-printed denture bases after aging by thermocycling: An in vitro study

Victor Augusto Alves Bento, João Mateus Cavalaro Sayeg, Cleber Davi Del Rei Daltro Rosa, Leonardo Ferreira de Toledo Piza Lopes, Maria Carolina Silva Marques, Eduardo Piza Pellizzer

The Journal of Indian Prosthodontic Society · 2025

DOI: 10.4103/jips.jips_88_25 ↗

Kurz gefasst

Fachartikel in der Zeitschrift The Journal of Indian Prosthodontic Society, 2025. Verfasst von Victor Augusto Alves Bento und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department Dental School, Federal University of Mato Grosso do Sul, Campo Grande, MS, Brazil. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Candida albicans, Computer-Aided Design, Denture Bases. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-SA 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Aim

The purpose of this study was to evaluate the surface properties, optical stability, and Candida albicans adhesion to resins used in the base of conventional, milled, and three-dimensional (3D)-printed dentures after aging by thermocycling. Settings and Design: In vitro study. Materials and Methods: A total of 96 resin samples were manufactured, divided into 3 resin groups ( n = 32) (conventional thermally activated, milled and 3D-printed), and subdivided into 4 aging times by thermocycling at temperatures 5 ± 1°C and 55 ± 1°C in 24h, 5.000, 10.000, 20.000 cycles ( n = 8), evaluating the adhesion of C. albicans , optical stability, surface roughness, hydrophilicity, and energy surface. Statistical Analysis Used: Data were evaluated by two-way ANOVA and Tukey’s test for pairwise comparisons ( P < .05).

Results

Conventional resin exhibited lower C. albicans colonization, with significant reductions at T1 (1.05±1.38) ( P = .003) and T3 (3.67 ±1.86) ( P = .023) compared to other resins. The conventional resin had significantly the lowest ΔE00 value at T0 (0.98 ± 0.41) ( P < .05). The milled resin had significantly lower roughness value at T0 (0.031 ± 0.00) ( P < .05). The conventional resin had significantly higher surface energy values compared to the other resins ( P < .05). The conventional resin exhibited a significantly lower water contact angle than the other resins ( P < .001).

Conclusion

The conventional thermally activated resin showed less adhesion of C. albicans than the resins manufactured by CAD/CAM. Among CAD/CAM resins, milled resin showed better properties than 3D-printed resin over time.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalCandida albicansComputer-Aided DesignDenture BasesSurface PropertiesIn Vitro TechniquesMaterials TestingHydrophobic and Hydrophilic InteractionsTemperatureHumans

Stichwörter der Autor:innen

computer-aided design/computer-aided manufacturingdenture stomatitisdentures

Autor:innen und Institutionen

  • Department Dental School, Federal University of Mato Grosso do Sul, Campo Grande, MS, Brazil.
  • Department of Dental Materials and Prosthodontics, Araçatuba Dental School, UNESP - Univ Estadual Paulista, Araçatuba, Sao Paulo, Brazil.
  • Department Microbiology, Center for Biological and Health Sciences, Federal University of Mato Grosso do Sul, Campo Grande, MS, Brazil.

Zitieren

APA

Bento, V. A. A., Sayeg, J. M. C., Rosa, C. D. D. R. D., Lopes, L. F. T. P., Marques, M. C. S., & Pellizzer, E. P. (2025). Evaluation of optical, surface, and microbiological properties of computer-aided design/computer-aided manufacturing-milled and three-dimensional-printed denture bases after aging by thermocycling: An in vitro study. The Journal of Indian Prosthodontic Society. https://doi.org/10.4103/jips.jips_88_25

Vancouver

Bento VAA, Sayeg JMC, Rosa CDDRD, Lopes LFTP, Marques MCS, Pellizzer EP. Evaluation of optical, surface, and microbiological properties of computer-aided design/computer-aided manufacturing-milled and three-dimensional-printed denture bases after aging by thermocycling: An in vitro study. The Journal of Indian Prosthodontic Society. 2025. doi:10.4103/jips.jips_88_25

BibTeX
@article{Bento2025,
  author = {Bento, Victor Augusto Alves and Sayeg, João Mateus Cavalaro and Rosa, Cleber Davi Del Rei Daltro and Lopes, Leonardo Ferreira de Toledo Piza and Marques, Maria Carolina Silva and Pellizzer, Eduardo Piza},
  title = {Evaluation of optical, surface, and microbiological properties of computer-aided design/computer-aided manufacturing-milled and three-dimensional-printed denture bases after aging by thermocycling: An in vitro study},
  journal = {The Journal of Indian Prosthodontic Society},
  year = {2025},
  doi = {10.4103/jips.jips_88_25}
}
Kostenlos starten →