Comparison of Mechanical and Surface Properties of 3D Printed and CAD-CAM Milled Resins for Interim Crowns - An In vitro Study
Indian Journal of Dental Research · 2025-10 · 36 (4) · 444-449
DOI: 10.4103/ijdr.ijdr_804_24 ↗Kurz gefasst
Vergleichsstudie in der Zeitschrift Indian Journal of Dental Research, online erschienen am 23.03.2026. Verfasst von Marine Ortiz-Magdaleno und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Aesthetic, Cosmetic, Restorative, and Implant Dentistry, San Luis Potosi, Mexico. Hauptthemen laut MEDLINE: Computer-Aided Design, Crowns, Printing, Three-Dimensional, Dental Prosthesis Design. Die Arbeit nennt 18 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).
Abstract (Originalsprache)
Context
For the success of the definitive restoration, interim prostheses are essential to maintain function in the complex environment of the oral cavity.
Aim
The aim was to characterize the mechanical properties and the surface of interim restoration material fabricated for fixed dental prostheses using two digital methods. Materials and Methods: Specimens were fabricated with computer-aided design and computer-aided manufacturing (CAD-CAM), milled polymethyl methacrylate (PMMA), and three-dimensional (3D) printed resin. The topography, roughness, and Vickers hardness number (VHN) of polished and unpolished surfaces were evaluated. The cement film was observed with confocal microscopy. The flexural strength and maximum force at fracture of cemented molar single-unit crowns were determined. Statistical Analysis: The mean values of the groups were analyzed by using the Shapiro-Wilk test and 1-way analysis of variance ( α = 0.05).
Results
In both techniques, no statistically significant differences were found in the VHN ( P > 0.05); the roughness values of the unpolished surface increased significantly ( P = 0.002). The topographic information showed that CAD-CAM milled PMMA and 3D printed resin had a smooth surface after polishing, and a cement film was observed on all the walls of the abutment surface. The flexural strength ( P = 0.001) and the mean maximum failure load ( P = 0.002) were significantly higher for CAD-CAM milled PMMA. The failure of CAD-CAM milled PMMA crowns was classified as minimal fracture; for the 3D printed resin crowns, the fracture was through the midline.
Conclusion
Both techniques provided clinically acceptable surfaces. CAD-CAM milled PMMA exhibited significantly higher failure at maximum load than 3D printed resin.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Department of Aesthetic, Cosmetic, Restorative, and Implant Dentistry, San Luis Potosi, Mexico.
- Department of Dental Science Advanced Education, Faculty of Stomatology, Autonomous University of San Luis Potosi, San Luis Potosi, Mexico.
- Department of Physics, Graduate Laboratory of Polymers, Institute of Physics, San Luis Potosi, Mexico.
- Department of Digital Dentistry, Faculty of Stomatology, Autonomous University of San Luis Potosi, San Luis Potosi, Mexico.
Zitieren
APA
Ortiz-Magdaleno, M., Chávez-Ponce, A., Zavala-Alonso, N. V., Armendáriz-Alonso, E. F., & Rodríguez-Urbina, V. E. (2025). Comparison of Mechanical and Surface Properties of 3D Printed and CAD-CAM Milled Resins for Interim Crowns - An In vitro Study. Indian Journal of Dental Research, 36(4), 444-449. https://doi.org/10.4103/ijdr.ijdr_804_24
Vancouver
Ortiz-Magdaleno M, Chávez-Ponce A, Zavala-Alonso NV, Armendáriz-Alonso EF, Rodríguez-Urbina VE. Comparison of Mechanical and Surface Properties of 3D Printed and CAD-CAM Milled Resins for Interim Crowns - An In vitro Study. Indian Journal of Dental Research. 2025;36(4):444-449. doi:10.4103/ijdr.ijdr_804_24
BibTeX
@article{OrtizMagdaleno2025,
author = {Ortiz-Magdaleno, Marine and Chávez-Ponce, Analí and Zavala-Alonso, Norma V and Armendáriz-Alonso, Edgard F and Rodríguez-Urbina, Victor E},
title = {Comparison of Mechanical and Surface Properties of 3D Printed and CAD-CAM Milled Resins for Interim Crowns - An In vitro Study},
journal = {Indian Journal of Dental Research},
year = {2025},
volume = {36},
number = {4},
pages = {444--449},
doi = {10.4103/ijdr.ijdr_804_24}
}
EUVIMED