Which cleaning protocols best preserve the surface roughness and hardness of occlusal devices produced by additive, subtractive, and conventional manufacturing?
The Journal of Prosthetic Dentistry · 2025
DOI: 10.1016/j.prosdent.2025.06.031 ↗Kurz gefasst
Fachartikel in der Zeitschrift The Journal of Prosthetic Dentistry, 2025. Verfasst von Izim Turker Kader und 3 weiteren Autor:innen. Beteiligte Einrichtung: Assistant Professor, Department of Prosthodontics, School of Dental Medicine, Bahçeşehir University, Istanbul, Turkey. Electronic address: izim.turke…. Hauptthemen laut MEDLINE: Dental Prosthesis Design. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 46 Literaturangaben.
Abstract (Originalsprache)
STATEMENT OF PROBLEM: Different cleaning protocols may alter the surface integrity of occlusal devices, yet their effects on devices fabricated by additive, subtractive, and conventional methods remain unclear. PURPOSE: The purpose of this in vitro study was to evaluate the effects of different cleaning protocols on the surface roughness and hardness of heat-polymerized polymethylmethacrylate (PMMA), computer-aided design and computer-aided manufacturing (CAD-CAM)-milled, and 3-dimensionally (3D) printed occlusal devices. MATERIAL AND METHODS: One hundred eighty disk-shaped specimens (Ø16×3 mm) were fabricated from 3 occlusal device materials: heat-polymerized PMMA (HP), CAD-CAM-milled (ML), and 3D printed resin (3D). After baseline surface roughness (Ra) and Vickers hardness (VHN) measurements, the specimens were divided into 6 cleaning groups (n=10): brushing with toothpaste (TP) or liquid soap (LS), immersion in chemical cleansers including effervescent denture cleansers (COR or CRP), a clove oil-based solution (EO), or distilled water (CON). TP and LS groups underwent 5000 brushing strokes, while chemical groups were subjected to 9 immersion cycles over 20 days, simulating 6 months of daily use. Ra and VHN were measured after exposure. Data were analyzed using mixed-design ANOVA and the post hoc Tukey HSD test (α=.05). RESULTS: ML exhibited the lowest Ra and highest VHN, while 3D showed the most significant changes over time (P
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Assistant Professor, Department of Prosthodontics, School of Dental Medicine, Bahçeşehir University, Istanbul, Turkey. Electronic address: izim.turker@gmail.com.
- PhD Candidate, Department of Prosthodontics, Faculty of Dentistry, Yeditepe University, Istanbul, Turkey.
- Professor, Department of Prosthodontics, Faculty of Dentistry, Yeditepe University, Istanbul, Turkey.
Zitieren
APA
Turker Kader, I., Barut, P., Karacan, E., & Kursoglu, P. (2025). Which cleaning protocols best preserve the surface roughness and hardness of occlusal devices produced by additive, subtractive, and conventional manufacturing?. The Journal of Prosthetic Dentistry. https://doi.org/10.1016/j.prosdent.2025.06.031
Vancouver
Turker Kader I, Barut P, Karacan E, Kursoglu P. Which cleaning protocols best preserve the surface roughness and hardness of occlusal devices produced by additive, subtractive, and conventional manufacturing?. The Journal of Prosthetic Dentistry. 2025. doi:10.1016/j.prosdent.2025.06.031
BibTeX
@article{TurkerKader2025,
author = {Turker Kader, Izim and Barut, Puren and Karacan, Ecem and Kursoglu, Pinar},
title = {Which cleaning protocols best preserve the surface roughness and hardness of occlusal devices produced by additive, subtractive, and conventional manufacturing?},
journal = {The Journal of Prosthetic Dentistry},
year = {2025},
doi = {10.1016/j.prosdent.2025.06.031}
}
EUVIMED