Comparative Evaluation of Three-dimensional-printed and Conventional Heat-cure Polymethyl Methacrylate Denture Base Materials
Annals of African Medicine · 2026-07-30
DOI: 10.4103/aam.aam_320_26 ↗At a glance
Journal article in Annals of African Medicine, published online on 2026-07-30. Written by Abdulrahman Mohammed Alduhailan and 6 co-authors. Institution: Department of Oral and Maxillofacial Surgery and Diagnostic Sciences, College of Dentistry, King Faisal University, Al-Ahsa, Saudi Arabia.
Abstract (original language)
Introduction
The introduction of three-dimensional (3D) printing in prosthodontics has revolutionized denture fabrication. However, the concerns remain regarding the mechanical and physicochemical properties of 3D-printed polymethyl methacrylate (PMMA) in comparison to conventional materials. This research was done to evaluate and compare the physicochemical and mechanical properties of a novel 3D-printed PMMA-based denture base material with conventional heat-polymerized PMMA. Materials and Methods: An in vitro experimental study was conducted on 98 specimens divided into two groups ( n = 49 each): Group I (3D-printed PMMA) and Group II (conventional PMMA). Specimens were fabricated using standardized protocols and evaluated for flexural strength, water sorption, surface roughness, surface hardness, impact strength, and solubility as per ISO guidelines. The obtained data were statistically evaluated.
Results
Group II demonstrated significantly higher mechanical properties, including flexural strength (92.63 ± 7.54 MPa), hardness (22.74 ± 2.01 VHN), and impact strength (4.05 ± 0.52 kJ/m 2 ) compared to Group I. Conversely, Group I exhibited higher surface roughness (0.42 ± 0.06 μm), water sorption (28.75 ± 3.21 μg/mm 3 ), and solubility (2.94 ± 0.51 μg/mm 3 ). All differences were statistically highly significant ( P < 0.001). Strong negative correlations were found between physicochemical and mechanical parameters.
Conclusion
Although 3D-printed PMMA offers advantages in digital dentistry, its inferior mechanical properties and higher degradation potential limit its current clinical applicability.
Subjects
Author keywords
Authors and institutions
- Department of Oral and Maxillofacial Surgery and Diagnostic Sciences, College of Dentistry, King Faisal University, Al-Ahsa, Saudi Arabia.
- Department of Public Health Dentistry, Luxmi Bai Institute of Dental Sciences and Hospital, Patiala, Punjab, India.
- Department of Biomedical Sciences, College of Medicine, King Faisal University, Al-Ahsa, Saudi Arabia.
- Department of Pharmaceutical Sciences, College of Clinical Pharmacy, King Faisal University, Al-Ahsa, Saudi Arabia.
- Department of Periodontology, Kalinga Institute of Dental Sciences, Bhubaneswar, Odisha, India.
- Consultant, Prosthodontist and Maxillofacial Prosthetist, Sanjeevini Hospital, New Delhi, India.
Cite
APA
Alduhailan, A. M., Mitra, P., Jasthi, V. C., Meravanige, G., Nagaraja, S., Mohapatra, A., & Jameel, A. S. (2026). Comparative Evaluation of Three-dimensional-printed and Conventional Heat-cure Polymethyl Methacrylate Denture Base Materials. Annals of African Medicine. https://doi.org/10.4103/aam.aam_320_26
Vancouver
Alduhailan AM, Mitra P, Jasthi VC, Meravanige G, Nagaraja S, Mohapatra A, et al. Comparative Evaluation of Three-dimensional-printed and Conventional Heat-cure Polymethyl Methacrylate Denture Base Materials. Annals of African Medicine. 2026. doi:10.4103/aam.aam_320_26
BibTeX
@article{Alduhailan2026,
author = {Alduhailan, Abdulrahman Mohammed and Mitra, Pranjan and Jasthi, Veeriah Chowdary and Meravanige, Girish and Nagaraja, Sreeharsha and Mohapatra, Arpita and Jameel, Ahmad Saib},
title = {Comparative Evaluation of Three-dimensional-printed and Conventional Heat-cure Polymethyl Methacrylate Denture Base Materials},
journal = {Annals of African Medicine},
year = {2026},
doi = {10.4103/aam.aam_320_26}
}
EUVIMED