EUVIMEDEUVIMED entdecken
Crossref

Comparative Evaluation of Three-dimensional-printed and Conventional Heat-cure Polymethyl Methacrylate Denture Base Materials

Abdulrahman Mohammed Alduhailan, Pranjan Mitra, Veeriah Chowdary Jasthi, Girish Meravanige, Sreeharsha Nagaraja, Arpita Mohapatra, Ahmad Saib Jameel

Annals of African Medicine · 30.07.2026

DOI: 10.4103/aam.aam_320_26 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Annals of African Medicine, online erschienen am 30.07.2026. Verfasst von Abdulrahman Mohammed Alduhailan und 6 weiteren Autor:innen. Beteiligte Einrichtung: Department of Oral and Maxillofacial Surgery and Diagnostic Sciences, College of Dentistry, King Faisal University, Al-Ahsa, Saudi Arabia.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Introduction

The introduction of three-dimensional (3D) printing in prosthodontics has revolutionized denture fabrication. However, the concerns remain regarding the mechanical and physicochemical properties of 3D-printed polymethyl methacrylate (PMMA) in comparison to conventional materials. This research was done to evaluate and compare the physicochemical and mechanical properties of a novel 3D-printed PMMA-based denture base material with conventional heat-polymerized PMMA. Materials and Methods: An in vitro experimental study was conducted on 98 specimens divided into two groups ( n = 49 each): Group I (3D-printed PMMA) and Group II (conventional PMMA). Specimens were fabricated using standardized protocols and evaluated for flexural strength, water sorption, surface roughness, surface hardness, impact strength, and solubility as per ISO guidelines. The obtained data were statistically evaluated.

Results

Group II demonstrated significantly higher mechanical properties, including flexural strength (92.63 ± 7.54 MPa), hardness (22.74 ± 2.01 VHN), and impact strength (4.05 ± 0.52 kJ/m 2 ) compared to Group I. Conversely, Group I exhibited higher surface roughness (0.42 ± 0.06 μm), water sorption (28.75 ± 3.21 μg/mm 3 ), and solubility (2.94 ± 0.51 μg/mm 3 ). All differences were statistically highly significant ( P < 0.001). Strong negative correlations were found between physicochemical and mechanical parameters.

Conclusion

Although 3D-printed PMMA offers advantages in digital dentistry, its inferior mechanical properties and higher degradation potential limit its current clinical applicability.

Schlagwörter

Stichwörter der Autor:innen

Additive manufacturingFabrication additivedenture base resinimpression tridimensionnellemechanical propertiespolymethyl methacrylatepolyméthacrylate de méthylepropriétés mécaniquesrugosité de surfacerésine pour base de prothèsesorption d’eausurface roughnessthree-dimensional printingwater sorption

Autor:innen und Institutionen

  • Department of Oral and Maxillofacial Surgery and Diagnostic Sciences, College of Dentistry, King Faisal University, Al-Ahsa, Saudi Arabia.
  • Department of Public Health Dentistry, Luxmi Bai Institute of Dental Sciences and Hospital, Patiala, Punjab, India.
  • Department of Biomedical Sciences, College of Medicine, King Faisal University, Al-Ahsa, Saudi Arabia.
  • Department of Pharmaceutical Sciences, College of Clinical Pharmacy, King Faisal University, Al-Ahsa, Saudi Arabia.
  • Department of Periodontology, Kalinga Institute of Dental Sciences, Bhubaneswar, Odisha, India.
  • Consultant, Prosthodontist and Maxillofacial Prosthetist, Sanjeevini Hospital, New Delhi, India.

Zitieren

APA

Alduhailan, A. M., Mitra, P., Jasthi, V. C., Meravanige, G., Nagaraja, S., Mohapatra, A., & Jameel, A. S. (2026). Comparative Evaluation of Three-dimensional-printed and Conventional Heat-cure Polymethyl Methacrylate Denture Base Materials. Annals of African Medicine. https://doi.org/10.4103/aam.aam_320_26

Vancouver

Alduhailan AM, Mitra P, Jasthi VC, Meravanige G, Nagaraja S, Mohapatra A, et al. Comparative Evaluation of Three-dimensional-printed and Conventional Heat-cure Polymethyl Methacrylate Denture Base Materials. Annals of African Medicine. 2026. doi:10.4103/aam.aam_320_26

BibTeX
@article{Alduhailan2026,
  author = {Alduhailan, Abdulrahman Mohammed and Mitra, Pranjan and Jasthi, Veeriah Chowdary and Meravanige, Girish and Nagaraja, Sreeharsha and Mohapatra, Arpita and Jameel, Ahmad Saib},
  title = {Comparative Evaluation of Three-dimensional-printed and Conventional Heat-cure Polymethyl Methacrylate Denture Base Materials},
  journal = {Annals of African Medicine},
  year = {2026},
  doi = {10.4103/aam.aam_320_26}
}
Kostenlos starten →