Improving HDI Substrate Reliability by Suppressing Void Growth in Electroless Cu Plating at Microvia Bottoms
IMAPSource Proceedings · 04.11.2026 · 2026 (Symposium)
DOI: 10.4071/001c.173568 ↗Kurz gefasst
Fachartikel in der Zeitschrift IMAPSource Proceedings, online erschienen am 04.11.2026. Verfasst von Ming-chun Hsieh und 8 weiteren Autor:innen.
Abstract (Originalsprache)
High-density interconnect (HDI) packaging substrates rely on stacked microvias for vertical electrical connection between build-up layers. However, the microvia bottom remains a critical reliability weak point during field use because repeated temperature variations can promote crack initiation near the electroless Cu plating layer. Voids formed in the electroless Cu layer have been suspected to contribute to weak-microvia failure, but the connection between void-growth mechanism, plating process control, and substrate-level reliability evaluation has not been fully clarified. This paper integrates two related studies on electroless Cu voiding and HDI substrate reliability. First, based on our previous mechanistic study, model multilayer Cu structures simulating the microvia-bottom region were prepared, and the effects of Ni concentration and bath temperature on electroless plating rate and void formation were investigated. TEM observation and quantitative image analysis showed that the largest voids and highest void fractions were formed in the initial deposition region. These results indicate that void growth is strongly governed by the initial plating stage, where Pd catalyst sites remain exposed and locally enhance the electroless Cu reaction and hydrogen generation. Under higher initial plating-rate conditions, hydrogen bubbles are more readily retained and coalesced, resulting in larger voids. Second, HDI substrates with identical designs but different electroless Cu voiding levels at the microvia bottoms were evaluated by thermal cycling tests (TCTs). The substrate with higher voiding exhibited lower reliability when the upper temperature (Thigh) of thermal cycling was near but below the glass transition temperature, Tg, of the insulation film. However, when Thigh exceeded Tg, the reliability difference between substrates became less distinguishable. These results indicate that suppressing the initial electroless Cu plating rate is an effective process guideline for reducing void formation and improving microvia reliability. They also show that reliability test conditions must be selected carefully with respect to insulation film Tg because excessively severe thermal cycling can obscure differences in interconnection quality.
Zitieren
APA
Hsieh, M., Nishijima, M., Suetake, A., Nakagiri, T., Yamanaka, K., Kitahara, Y., Yoshikawa, J., Nishikawa, H., & Suganuma, K. (2026). Improving HDI Substrate Reliability by Suppressing Void Growth in Electroless Cu Plating at Microvia Bottoms. IMAPSource Proceedings, 2026(Symposium). https://doi.org/10.4071/001c.173568
Vancouver
Hsieh M, Nishijima M, Suetake A, Nakagiri T, Yamanaka K, Kitahara Y, et al. Improving HDI Substrate Reliability by Suppressing Void Growth in Electroless Cu Plating at Microvia Bottoms. IMAPSource Proceedings. 2026;2026(Symposium). doi:10.4071/001c.173568
BibTeX
@article{Hsieh2026,
author = {Hsieh, Ming-chun and Nishijima, Masahiko and Suetake, Aiji and Nakagiri, Takuya and Yamanaka, Kimihiro and Kitahara, Yuhei and Yoshikawa, Junichi and Nishikawa, Hiroshi and Suganuma, Katsuaki},
title = {Improving HDI Substrate Reliability by Suppressing Void Growth in Electroless Cu Plating at Microvia Bottoms},
journal = {IMAPSource Proceedings},
year = {2026},
volume = {2026},
number = {Symposium},
doi = {10.4071/001c.173568}
}
EUVIMED