EUVIMEDEUVIMED entdecken
Crossref

Evaluation of Innovative Nano-Coated Stencils in Ultra-Fine-Pitch Flip Chip Bumping Processes

Dionysios Manessis, Rainer Patzelt, Andreas Ostmann, Rolf Aschenbrenner, Herbert Reichl, Andreas Axmann, Carmina Laentzsch, Georg Kleemann

IMAPSource Proceedings · 20.07.2026 · 2008 (Symposium)

DOI: 10.4071/001c.165299 ↗

Kurz gefasst

Fachartikel in der Zeitschrift IMAPSource Proceedings, online erschienen am 20.07.2026. Verfasst von Dionysios Manessis und 7 weiteren Autor:innen.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Stencil printing remains the technology route of choice for flip chip bumping because of its economical advantages over traditionally costly evaporation and electroplating processes. This paper brings up all the technological challenges and up to date advancements in all processing steps of 6”wafer bumping of peripheral array structures at Ultra-fine-pitches (UFP) of 80μm and 60μm pitch. Innovative laser-cut stencils with nano-treatment of the sidewalls and the bottom surface have been manufactured with a thickness down to 20μm and apertures of 40μmx100μm and 35μmx80μm, respectively. Both type 6 (5-15μm) and type 8 (2-8μm) pastes of lead-free Sn4Ag0.5Cu compositions have been successfully employed for wafer bumping at 80μm and 60μm pitch. Bumping using a 20 μm laser-cut nano-treated stencil has yielded a bump height of 23μm. Nano-treatment of stencils improves significantly the paste release from apertures even for very fine apertures. In addition, nano-stencils may extend the use of commercial type 6 pastes for pitches even smaller than 100μm due to improved paste release. Printing results with nano-stencils are very promising even at aspect and area ratios smaller than 1.5 and 0.66 which have been considered as the “rules of thumbs” for stencil printing. The combination of type 8 paste printing and nano-treatment can open new horizons for stencil printing at pitches even smaller than 80μm. Bumping at 80μm pitch with laser-cut stencils yields bumps of 23μm. Printing at 60μm pitch has also yielded very promising results and has proved the capability of electroformed technology to manufacture accurate and robust thin stencils. The bump height at 60μm pitch was measured to be 28 ±3 μm.

Zitieren

APA

Manessis, D., Patzelt, R., Ostmann, A., Aschenbrenner, R., Reichl, H., Axmann, A., Laentzsch, C., & Kleemann, G. (2026). Evaluation of Innovative Nano-Coated Stencils in Ultra-Fine-Pitch Flip Chip Bumping Processes. IMAPSource Proceedings, 2008(Symposium). https://doi.org/10.4071/001c.165299

Vancouver

Manessis D, Patzelt R, Ostmann A, Aschenbrenner R, Reichl H, Axmann A, et al. Evaluation of Innovative Nano-Coated Stencils in Ultra-Fine-Pitch Flip Chip Bumping Processes. IMAPSource Proceedings. 2026;2008(Symposium). doi:10.4071/001c.165299

BibTeX
@article{Manessis2026,
  author = {Manessis, Dionysios and Patzelt, Rainer and Ostmann, Andreas and Aschenbrenner, Rolf and Reichl, Herbert and Axmann, Andreas and Laentzsch, Carmina and Kleemann, Georg},
  title = {Evaluation of Innovative Nano-Coated Stencils in Ultra-Fine-Pitch Flip Chip Bumping Processes},
  journal = {IMAPSource Proceedings},
  year = {2026},
  volume = {2008},
  number = {Symposium},
  doi = {10.4071/001c.165299}
}
Kostenlos starten →