EUVIMEDEUVIMED entdecken
Crossref

Optimization of Copper Electroplating Parameters for SLA-Printed EDM Electrodes

Shahrul Nizam Abdul Rahman, Reazul Haq Abdul Haq, Mohammad Fahmi Abdul Ghafir, Bukhari Manshoor, Said Ahmad, Sharifah Adzila, Sanusi Sanusi, Yashvir Singh

Solid State Phenomena · 23.11.2026 · 396 · 113-120

DOI: 10.4028/p-wrd3ku ↗

Kurz gefasst

Fachartikel in der Zeitschrift Solid State Phenomena, online erschienen am 23.11.2026. Verfasst von Shahrul Nizam Abdul Rahman und 7 weiteren Autor:innen. Die Arbeit nennt 12 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Stereolithography (SLA) 3D printing offers high dimensional accuracy and design flexibility, making it suitable for fabricating complex Electrical Discharge Machining (EDM) electrodes. However, the non-conductive nature of SLA-printed resin limits its direct application in EDM processes. This study investigates the feasibility of producing conductive EDM electrodes by integrating SLA 3D printing with copper electroplating. Cylindrical electrodes were fabricated using high-temperature SLA resin and subsequently metallized using a conductive coating to enable electroplating. Copper electroplating was carried out using a copper sulphate–sulphuric acid electrolyte, with a fixed copper sulphate content of 55 g per 250 ml of solution. Sulphuric acid concentration, applied current, and plating time were selected as the main process parameters. Sulphuric acid concentrations of 11 ml, 14.5 ml, and 18 ml per 250 ml solution were investigated, along with current values of 0.06 A, 0.09 A, and 0.11 A, and plating durations of 3, 6, and 9 hours. Electrical resistance and coating thickness were measured as the primary response variables. A Design of Experiment (DOE) approach was employed to evaluate the influence of electroplating parameters on electrical resistance. Analysis of Variance (ANOVA) results indicated that plating time had the most significant effect on electrical resistance, while sulphuric acid concentration and current showed less pronounced influence within the tested range. A quadratic model was selected as the most suitable representation of the experimental data due to its acceptable fit and absence of significant lack of fit, although its predictive capability was limited. The optimized parameter combination suggested by the model consisted of 14.5 ml sulphuric acid per 250 ml solution, a current of 0.085 A, and a plating time of 6 hours. Overall, the results demonstrate that copper electroplating effectively enhances the electrical resistance of SLA-printed electrodes, highlighting their potential as cost-effective alternatives to conventionally manufactured EDM electrodes through a hybrid manufacturing approach.

Zitieren

APA

Rahman, S. N. A., Haq, R. H. A., Ghafir, M. F. A., Manshoor, B., Ahmad, S., Adzila, S., Sanusi, S., & Singh, Y. (2026). Optimization of Copper Electroplating Parameters for SLA-Printed EDM Electrodes. Solid State Phenomena, 396, 113-120. https://doi.org/10.4028/p-wrd3ku

Vancouver

Rahman SNA, Haq RHA, Ghafir MFA, Manshoor B, Ahmad S, Adzila S, et al. Optimization of Copper Electroplating Parameters for SLA-Printed EDM Electrodes. Solid State Phenomena. 2026;396:113-120. doi:10.4028/p-wrd3ku

BibTeX
@article{Rahman2026,
  author = {Rahman, Shahrul Nizam Abdul and Haq, Reazul Haq Abdul and Ghafir, Mohammad Fahmi Abdul and Manshoor, Bukhari and Ahmad, Said and Adzila, Sharifah and Sanusi, Sanusi and Singh, Yashvir},
  title = {Optimization of Copper Electroplating Parameters for SLA-Printed EDM Electrodes},
  journal = {Solid State Phenomena},
  year = {2026},
  volume = {396},
  pages = {113--120},
  doi = {10.4028/p-wrd3ku}
}
Kostenlos starten →