EUVIMEDSkopri EUVIMED
Video/Audio

Fabrication of Bi2Te3 and Sb2Te3 Thermoelectric Thin Films using Radio Frequency Magnetron Sputtering Technique

Nurfarhana Ahmad Musri, Yoganash Putthisigamany, Puvaneswaran Chelvanathan, Norasikin Ahmad Ludin, Nadhrah Md Yatim, Ubaidah Syafiq

Journal of Visualized Experiments · 2024

DOI: 10.3791/66248 ↗

At a glance

Video/Audio in Journal of Visualized Experiments, 2024. Written by Nurfarhana Ahmad Musri and 5 co-authors. Institution: Solar Energy Research Institute (SERI), Universiti Kebangsaan Malaysia; P130552@siswa.ukm.edu.my. Major MEDLINE topics: Bismuth, Antimony, Tellurium. Cited 4 times so far (Crossref); 52 references.

AstrattSubjectsDettalji biblijografiċiCiteRelated studies

Abstract (original language)

Through various studies on thermoelectric (TE) materials, thin film configuration gives superior advantages over conventional bulk TEs, including adaptability to curved and flexible substrates. Several different thin film deposition methods have been explored, yet magnetron sputtering is still favorable due to its high deposition efficiency and scalability. Therefore, this study aims to fabricate a bismuth telluride (Bi2Te3) and antimony telluride (Sb2Te3) thin film via the radio frequency (RF) magnetron sputtering method. The thin films were deposited on soda lime glass substrates at ambient temperature. The substrates were first washed using water and soap, ultrasonically cleaned with methanol, acetone, ethanol, and deionized water for 10 min, dried with nitrogen gas and hot plate, and finally treated under UV ozone for 10 min to remove residues before the coating process. A sputter target of Bi2Te3 and Sb2Te3 with Argon gas was used, and pre-sputtering was done to clean the target's surface. Then, a few clean substrates were loaded into the sputtering chamber, and the chamber was vacuumed until the pressure reached 2 x 10-5 Torr. The thin films were deposited for 60 min with Argon flow of 4 sccm and RF power at 75 W and 30 W for Bi2Te3 and Sb2Te3, respectively. This method resulted in highly uniform n-type Bi2Te3 and p-type Sb2Te3 thin films.

Subjects

MeSH terms (MEDLINE)

BismuthAntimonyTelluriumRadio Waves

Substances

BismuthAntimonyTelluriumbismuth telluride

Authors and institutions

  • Solar Energy Research Institute (SERI), Universiti Kebangsaan Malaysia; P130552@siswa.ukm.edu.my.
  • Solar Energy Research Institute (SERI), Universiti Kebangsaan Malaysia.
  • Faculty of Science and Technology, Universiti Sains Islam Malaysia.
  • Solar Energy Research Institute (SERI), Universiti Kebangsaan Malaysia; ubaidahsyafiq@ukm.edu.my.

Cite

APA

Ahmad Musri, N., Putthisigamany, Y., Chelvanathan, P., Ahmad Ludin, N., Md Yatim, N., & Syafiq, U. (2024). Fabrication of Bi2Te3 and Sb2Te3 Thermoelectric Thin Films using Radio Frequency Magnetron Sputtering Technique. Journal of Visualized Experiments. https://doi.org/10.3791/66248

Vancouver

Ahmad Musri N, Putthisigamany Y, Chelvanathan P, Ahmad Ludin N, Md Yatim N, Syafiq U. Fabrication of Bi2Te3 and Sb2Te3 Thermoelectric Thin Films using Radio Frequency Magnetron Sputtering Technique. Journal of Visualized Experiments. 2024. doi:10.3791/66248

BibTeX
@article{AhmadMusri2024,
  author = {Ahmad Musri, Nurfarhana and Putthisigamany, Yoganash and Chelvanathan, Puvaneswaran and Ahmad Ludin, Norasikin and Md Yatim, Nadhrah and Syafiq, Ubaidah},
  title = {Fabrication of Bi2Te3 and Sb2Te3 Thermoelectric Thin Films using Radio Frequency Magnetron Sputtering Technique},
  journal = {Journal of Visualized Experiments},
  year = {2024},
  doi = {10.3791/66248}
}
Start for free →