Analysis of HSS and A420 Type Carbide Chisels on the Surface Quality of Fiberglass (GFRP) Rolls in the Turning Process
JTTM : Jurnal Terapan Teknik Mesin · 30.09.2026 · 7 (2) · 411-417
DOI: 10.37373/jttm.v7i2.2654 ↗Kurz gefasst
Fachartikel in der Zeitschrift JTTM : Jurnal Terapan Teknik Mesin, online erschienen am 30.09.2026. Verfasst von Achmad Nur Khaeri und 2 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0).
Abstract (Originalsprache)
Glass Fiber Reinforced Polymer (GFRP) is widely used in engineering applications because of its high strength-to-weight ratio, corrosion resistance, and dimensional stability. However, the abrasive nature and heterogeneous structure of GFRP can accelerate tool wear and reduce surface quality during machining. This study aims to compare the performance of High-Speed Steel (HSS) and A420 carbide cutting tools in the dry turning of GFRP rolls, using average surface roughness (Ra) as the primary response. The experiments were conducted at spindle speeds of 300, 600, 900, 1200, and 1500 RPM under constant machining conditions. Surface roughness was measured three times for each experimental condition, and the mean values were used for analysis. The results indicate that the A420 carbide tool consistently produced a smoother surface than the HSS tool at all spindle speeds. At 300 RPM, the carbide tool generated an average Ra of 2.00 µm, while the HSS tool produced 4.63 µm, representing a surface-roughness reduction of 56.80%. At 1500 RPM, the Ra value increased to 8.33 µm for HSS and 4.33 µm for carbide, corresponding to a 48.02% reduction. Surface roughness increased with increasing spindle speed for both tool materials, indicating that higher rotational speed under the tested dry-cutting conditions adversely affected surface quality. Overall, A420 carbide demonstrated better machining performance and is therefore more suitable than HSS for the dry turning of abrasive GFRP rolls. Further research should evaluate tool wear, cutting forces, feed rate, and depth of cut to determine comprehensive optimum machining parameters.
Zitieren
APA
Khaeri, A. N., Solihin, Z., & Pane, A. F. (2026). Analysis of HSS and A420 Type Carbide Chisels on the Surface Quality of Fiberglass (GFRP) Rolls in the Turning Process. JTTM : Jurnal Terapan Teknik Mesin, 7(2), 411-417. https://doi.org/10.37373/jttm.v7i2.2654
Vancouver
Khaeri AN, Solihin Z, Pane AF. Analysis of HSS and A420 Type Carbide Chisels on the Surface Quality of Fiberglass (GFRP) Rolls in the Turning Process. JTTM : Jurnal Terapan Teknik Mesin. 2026;7(2):411-417. doi:10.37373/jttm.v7i2.2654
BibTeX
@article{Khaeri2026,
author = {Khaeri, Achmad Nur and Solihin, Zainal and Pane, Akhmad Fauzi},
title = {Analysis of HSS and A420 Type Carbide Chisels on the Surface Quality of Fiberglass (GFRP) Rolls in the Turning Process},
journal = {JTTM : Jurnal Terapan Teknik Mesin},
year = {2026},
volume = {7},
number = {2},
pages = {411--417},
doi = {10.37373/jttm.v7i2.2654}
}
EUVIMED