Comparative deformation indices of FDM-printed PLA-LW structures across three infill topologies: Secant stiffness, apparent strain, and specific toughness
Materials Science in Additive Manufacturing · 20.08.2026 · 026220050
DOI: 10.36922/msam026220050 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials Science in Additive Manufacturing, online erschienen am 20.08.2026. Verfasst von Ahmad Alshwawra und 1 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref).
Abstract (Originalsprache)
Most characterisation work on fused deposition modelling-printed lightweight polylactic acid (PLA-LW) focuses on peak load resistance, leaving the pre-fracture deformation regime underexplored. This regime governs stiffness, deformation tolerance, and energy absorption per unit volume, and is decisive for deflection-limited and impact-tolerant lightweight components. In this study, three comparative mechanical indices were extracted from 114 quasi-static tensile records spanning Phase 1 (Cubic; eight temperatures; n = 6 per temperature) and Phase 2 (Cubic, Gyroid, Sub-Cubic; two temperatures and two flow rates; n = 3–6 per condition) at 20% infill ratio: the secant stiffness index Es, the apparent strain index εapp, and the specific toughness index U/ρ. Two Gyroid F80/240 °C specimens were excluded after stress–strain curve inspection revealed grip-slip artefacts, evidence as early-loading plateaus in which crosshead displacement is taken up by specimen seating and slip at the grips rather than by gauge-section deformation. The remaining three valid specimens at this condition were retained. Phase 1 ANOVA confirmed a highly significant temperature effect on Es (F(7,40) = 15.13, p < 0.001). Near the foaming onset (210 °C), Es peaked at 117.4 ± 10.7 MPa while εapp reached its descriptive minimum (F(7,40) = 1.80, p = 0.114 overall; F(6,35) = 1.07, p = 0.400 excluding 190 °C). In Phase 2, flow-rate effects on Es were significant for the Cubic (t(19.4) = 16.37, p < 0.001, d = 6.68) and Sub-Cubic (t(19.4) = 7.25, p < 0.001, d = 2.96). The Gyroid showed no significant flow-rate reversal (t(15.8) = −1.70, p = 0.108); however, both Gyroid flow-rate conditions exhibited a significant temperature sensitivity (F70: p = 0.006; F80: p = 0.005). Deformation-regime indices diverged substantially from strength trends; no single topology ranked highest across all three dimensions simultaneously. Future work should validate these comparative indices using extensometer or digital image correlation measurements.
Zitieren
APA
Alshwawra, A., & Alomari, M. H. (2026). Comparative deformation indices of FDM-printed PLA-LW structures across three infill topologies: Secant stiffness, apparent strain, and specific toughness. Materials Science in Additive Manufacturing, 0(0), 026220050. https://doi.org/10.36922/msam026220050
Vancouver
Alshwawra A, Alomari MH. Comparative deformation indices of FDM-printed PLA-LW structures across three infill topologies: Secant stiffness, apparent strain, and specific toughness. Materials Science in Additive Manufacturing. 2026;0(0):026220050. doi:10.36922/msam026220050
BibTeX
@article{Alshwawra2026,
author = {Alshwawra, Ahmad and Alomari, Mohammad Hani},
title = {Comparative deformation indices of FDM-printed PLA-LW structures across three infill topologies: Secant stiffness, apparent strain, and specific toughness},
journal = {Materials Science in Additive Manufacturing},
year = {2026},
volume = {0},
number = {0},
pages = {026220050},
doi = {10.36922/msam026220050}
}
EUVIMED