Laser-assisted cold spray additive manufacturing of Ti6Al4V: Synergistic evolution of microstructure refinement and interface bonding
Materials Science in Additive Manufacturing · 23.07.2026 · 5 (3) · 026220048
DOI: 10.36922/msam026220048 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials Science in Additive Manufacturing, online erschienen am 23.07.2026. Verfasst von Shaowu Liu und 11 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref).
Abstract (Originalsprache)
The aluminum/titanium (Al/Ti) couple is a typical “limited mutual solubility heterogeneous metal” system, in which fusion-based manufacturing often leads to brittle intermetallic compounds and cracks. This study systematically investigates the microstructure and mechanical properties of Ti6Al4V deposited on 6061Al substrates via laser-assisted cold spray (LACS). X-ray diffraction (XRD) results confirm that the process maintains solid-state deposition characteristics, with only the α-Ti phase detected, indicating no detectable Al/Ti intermetallic compounds by XRD across all conditions. Laser assistance significantly enhanced deposition layer densification; at 600 W, the porosity decreased from 11.81% to 0.41%. Electron backscatter diffraction and transmission electron microscopy (TEM) characterizations revealed that the LACS process triggered intense dynamic recrystallization, refining the average grain size from 1.906 μm to 0.813 μm. High-resolution TEM analysis further identified a nanoscale grain gradient and a ~5 μm elemental transition zone layer at the bonding interface, demonstrating the formation of a compositionally graded interfacial region accompanied by mechanical interlocking and localized elemental redistribution. Performance tests showed that increasing the laser power increased the microhardness to 388.1 HV0.2. Compared to cold spraying, the LACS-600 W samples achieved a 40% increase in ultimate tensile strength (206.58 MPa) and a 100% improvement in elongation (2.17%). The results indicate that LACS provides a high-performance solid-state additive manufacturing solution for Ti6Al4V/6061Al heterogeneous structures through the synergistic effects of laser-induced thermal accumulation and particle tamping densification.
Zitieren
APA
Liu, S., Wang, S., Zhang, Y., Wu, H., Li, W., Li, B., Yu, Z., Zhang, P., Yin, S., Zhang, Q., Liao, H., & Yao, J. (2026). Laser-assisted cold spray additive manufacturing of Ti6Al4V: Synergistic evolution of microstructure refinement and interface bonding. Materials Science in Additive Manufacturing, 5(3), 026220048. https://doi.org/10.36922/msam026220048
Vancouver
Liu S, Wang S, Zhang Y, Wu H, Li W, Li B, et al. Laser-assisted cold spray additive manufacturing of Ti6Al4V: Synergistic evolution of microstructure refinement and interface bonding. Materials Science in Additive Manufacturing. 2026;5(3):026220048. doi:10.36922/msam026220048
BibTeX
@article{Liu2026,
author = {Liu, Shaowu and Wang, Shen and Zhang, Yehao and Wu, Hongjian and Li, Wenbo and Li, Bo and Yu, Zexin and Zhang, Panpan and Yin, Shuo and Zhang, Qunli and Liao, Hanlin and Yao, Jianhua},
title = {Laser-assisted cold spray additive manufacturing of Ti6Al4V: Synergistic evolution of microstructure refinement and interface bonding},
journal = {Materials Science in Additive Manufacturing},
year = {2026},
volume = {5},
number = {3},
pages = {026220048},
doi = {10.36922/msam026220048}
}
EUVIMED