EUVIMEDEUVIMED entdecken
Crossref

Investigation of mechanical properties and thermal conductivity coefficients of 3D printer materials

Furkan PARMAKSIZ, Nergizhan ANAÇ, Oğuz KOÇAR, Beytullah ERDOGAN

International Advanced Researches and Engineering Journal · 15.12.2023 · 7 (3) · 146-156

DOI: 10.35860/iarej.1303538 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Advanced Researches and Engineering Journal, online erschienen am 15.12.2023. Verfasst von Furkan PARMAKSIZ und 3 weiteren Autor:innen. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 50 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The demand for 3D printer technology and products, one of the additive manufacturing methods, is increasing daily in the sectoral and academic fields. Many types of polymer-based filaments are used in 3D printers, pure or filled/reinforcement. Utilizing these specialized materials in places suitable for their mechanical and thermal properties will help efficiently use resources. Using 3D printers, it is possible to manufacture products that provide thermal insulation or good heat conduction in heating and cooling areas. Especially due to the energy requirements for heating and cooling, it is very important to know the thermal performance of materials to ensure and maintain energy efficiency. This study experimentally investigated the mechanical properties and heat conduction coefficients of 3D printed parts. The experiments were conducted with seven different filament materials (PLA, PLA+, PLA-CF, PLA Wood, Tough PLA, ABS+, TPU) and three layer thicknesses (0.1, 0.2, and 0.3 mm). Samples for tensile testing, hardness, and thermal conductivity coefficient measurements were produced, and measurements were performed. In the experiments, the highest tensile strength was obtained in PLA-CF with 0.3 mm layer thickness, and the lowest tensile strength was obtained in PLA Wood with 0.3 mm layer thickness. Tensile strength decreased with an increasing layer thickness in PLA, PLA Wood, ABS+, and TPU, while it increased in PLA-CF. The highest tensile strength of PLA+ was determined to be 0.2 mm and 0.1 mm layer thickness in Tough PLA. Hardness results showed minimal change in hardness values with increasing layer thickness. The thermal conductivity values of the samples varied according to the additives and layer thicknesses. The highest thermal conductivity increase was measured in PLA-CF with 11.84%, and the lowest thermal conductivity decrease was measured in Tough PLA with 9.44%.

Zitieren

APA

PARMAKSIZ, F., ANAÇ, N., KOÇAR, O., & ERDOGAN, B. (2023). Investigation of mechanical properties and thermal conductivity coefficients of 3D printer materials. International Advanced Researches and Engineering Journal, 7(3), 146-156. https://doi.org/10.35860/iarej.1303538

Vancouver

PARMAKSIZ F, ANAÇ N, KOÇAR O, ERDOGAN B. Investigation of mechanical properties and thermal conductivity coefficients of 3D printer materials. International Advanced Researches and Engineering Journal. 2023;7(3):146-156. doi:10.35860/iarej.1303538

BibTeX
@article{PARMAKSIZ2023,
  author = {PARMAKSIZ, Furkan and ANAÇ, Nergizhan and KOÇAR, Oğuz and ERDOGAN, Beytullah},
  title = {Investigation of mechanical properties and thermal conductivity coefficients of 3D printer materials},
  journal = {International Advanced Researches and Engineering Journal},
  year = {2023},
  volume = {7},
  number = {3},
  pages = {146--156},
  doi = {10.35860/iarej.1303538}
}
Kostenlos starten →