EUVIMEDEUVIMED entdecken
Crossref

Preheating Bulk-Fill Composite Resins: Effects on Microtensile Bond Strength to Dentin in High C-Factor Cavities

Ferdos Naserneysari, Sana Dibazar, Mahmoud Bahari, Mehdi Esmaeili

Journal of Dental Research, Dental Clinics, Dental Prospects · 30.09.2026 · 20 (3) · 172-175

DOI: 10.34172/joddd.44891 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Dental Research, Dental Clinics, Dental Prospects, online erschienen am 30.09.2026. Verfasst von Ferdos Naserneysari und 3 weiteren Autor:innen. Die Arbeit nennt 23 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Introduction

Preheating composite resins has been suggested as a practical strategy to reduce material viscosity and improve adaptation to cavity walls. This approach may be particularly advantageous in deep Class I cavities with a high C-factor, where reliable dentin bonding remains challenging. Nevertheless, evidence on the influence of composite resin preheating on the dentin bond strength of bulk-fill composite resins under these conditions remains limited. Therefore, this study evaluated the effect of composite resin preheating on the microtensile dentin bond strength of a bulk-fill composite resin in such cavities.

Methods

Thirty-six sound human mandibular third molars, extracted for orthodontic reasons, were included in this in vitro study. After debridement, the cusps were removed to obtain flat occlusal surfaces. Following acid etching and adhesive application, a 1-mm-thick composite resin layer was placed on the occlusal surface. Class I cavities were then prepared with the pulpal floor located in the mid-dentin region. The specimens were randomly allocated to two groups based on the composite resin preconditioning temperature. Composite resin syringes (x-tra fil) were stored in distilled water at either 23°C or 60°C for 30 minutes before placement. The cavities were subsequently restored, and the specimens were subjected to thermocycling prior to microtensile bond strength testing. Bond strength values (MPa) were compared using an independent-samples t-test.

Results

The preheated composite group demonstrated significantly higher microtensile bond strength than the room-temperature group (P=0.002).

Conclusion

Preheating the x-tra fil bulk-fill composite to 60°C significantly enhanced microtensile dentin bond strength in deep Class I cavities. Further studies are required to confirm the clinical relevance.

Zitieren

APA

Naserneysari, F., Dibazar, S., Bahari, M., & Esmaeili, M. (2026). Preheating Bulk-Fill Composite Resins: Effects on Microtensile Bond Strength to Dentin in High C-Factor Cavities. Journal of Dental Research, Dental Clinics, Dental Prospects, 20(3), 172-175. https://doi.org/10.34172/joddd.44891

Vancouver

Naserneysari F, Dibazar S, Bahari M, Esmaeili M. Preheating Bulk-Fill Composite Resins: Effects on Microtensile Bond Strength to Dentin in High C-Factor Cavities. Journal of Dental Research, Dental Clinics, Dental Prospects. 2026;20(3):172-175. doi:10.34172/joddd.44891

BibTeX
@article{Naserneysari2026,
  author = {Naserneysari, Ferdos and Dibazar, Sana and Bahari, Mahmoud and Esmaeili, Mehdi},
  title = {Preheating Bulk-Fill Composite Resins: Effects on Microtensile Bond Strength to Dentin in High C-Factor Cavities},
  journal = {Journal of Dental Research, Dental Clinics, Dental Prospects},
  year = {2026},
  volume = {20},
  number = {3},
  pages = {172--175},
  doi = {10.34172/joddd.44891}
}
Kostenlos starten →