EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Obtaining Symmetrical Gradient Structure in Copper Wire by Combined Processing

Andrey Volokitin, Irina Volokitina, Mehmet Seref Sonmez, Anastassiya Denissova, Zoya Gelmanova

Symmetry · 12.11.2024 · 16 (11) · 1515

DOI: 10.3390/sym16111515 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Symmetry, online erschienen am 12.11.2024. Verfasst von Andrey Volokitin und 4 weiteren Autor:innen. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Science Committee of the Ministry of Science and Higher Education of the Republic of Kazakhstan.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Traditionally, structural wire is characterized by a homogeneous microstructure, where the average grain size in different parts of the wire is uniform. According to the classical Hall–Petch relationship, a homogeneous polycrystalline metal can be strengthened by decreasing the average grain size since an increase in the volume fraction of grain boundaries will further impede the motion of dislocations. However, a decrease in the grain size inevitably leads to a decrease in the ductility and deformability of the material due to limited dislocation mobility. Putting a gradient microstructure into the wire has promising potential for overcoming the compromise between strength and ductility. This is proposed a new combined technology in this paper in order to obtain a gradient microstructure. This technology consists of deforming the wire in a rotating equal-channel step die and subsequent traditional drawing. Deformation of copper wire with a diameter of 6.5 mm to a diameter of 5.0 mm was carried out in three passes at room temperature. As a result of such processing, a gradient microstructure with a surface nanostructured layer (grain size ~400 nm) with a gradual increase in grain size towards the center of the wire was obtained. As a result, the microhardness in the surface zone was 1150 MPa, 770 Mpa in the neutral zone, and 685 MPa in the central zone of the wire. Such a symmetrical spread of microhardness, observed over the entire cross-section of the rod, is a direct confirmation of the presence of a gradient microstructure in deformed materials. The strength characteristics of the wire were doubled: the tensile strength increased from 335 MPa to 675 MPa, and the yield strength from 230 MPa to 445 MPa. At the same time, the relative elongation decreased from 20% to 16%, and the relative contraction from 28% to 23%. Despite the fact that the ductility of copper is decreased after cyclic deformation, its values remain at a fairly high level. The validity of all results is confirmed by numerous experiments using a complex of traditional and modern research methods, which include optical, scanning, and transmission microscopy; determination of mechanical properties under tension; and measurement of hardness and electrical resistance. These methods allow reliable interpretation of the fine microstructure of the wire and provide information on its strength, plastic, and electrical properties.

Förderung

  • Science Committee of the Ministry of Science and Higher Education of the Republic of Kazakhstan

Zitieren

APA

Volokitin, A., Volokitina, I., Sonmez, M. S., Denissova, A., & Gelmanova, Z. (2024). Obtaining Symmetrical Gradient Structure in Copper Wire by Combined Processing. Symmetry, 16(11), 1515. https://doi.org/10.3390/sym16111515

Vancouver

Volokitin A, Volokitina I, Sonmez MS, Denissova A, Gelmanova Z. Obtaining Symmetrical Gradient Structure in Copper Wire by Combined Processing. Symmetry. 2024;16(11):1515. doi:10.3390/sym16111515

BibTeX
@article{Volokitin2024,
  author = {Volokitin, Andrey and Volokitina, Irina and Sonmez, Mehmet Seref and Denissova, Anastassiya and Gelmanova, Zoya},
  title = {Obtaining Symmetrical Gradient Structure in Copper Wire by Combined Processing},
  journal = {Symmetry},
  year = {2024},
  volume = {16},
  number = {11},
  pages = {1515},
  doi = {10.3390/sym16111515}
}
Kostenlos starten →