Fabrication and Characterization of High-Performance Channel Electron Multipliers Using Alternating Acid and Base Etching and Atomic Layer Deposition
Surfaces · 19.11.2026 · 9 (4) · 97
DOI: 10.3390/surfaces9040097 ↗Kurz gefasst
Fachartikel in der Zeitschrift Surfaces, online erschienen am 19.11.2026. Verfasst von Zexun Hu und 9 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China.
Abstract (Originalsprache)
Channel electron multipliers (CEMs) are continuous dynode vacuum electronic devices used in residual gas analysis and mass spectrometry. Owing to the unique structure and intricate fabrication process of CEMs, developing ultra-high-gain, low-noise devices has long been a major engineering challenge worldwide. The CEM was fabricated from lead silicate glass by preform preparation, capillary drawing, inlet flaring, outlet bending, inlet shaping, cleaning, hydrogen reduction, sandblasting isolation, etching, electron-beam evaporation and atomic layer deposition. We characterized the inner-wall morphology and electrical properties following alternating acid and base etching and atomic layer deposition (ALD) using SEM/EDS, AFM, XPS and electrical measurements. Rounded elemental-lead particles (237 ± 31 nm in diameter) were observed on the channel wall after high-temperature hydrogen reduction. Alternating etching with 1.2 mol/L HCl and 8 wt.% NaOH reduced the root-mean-square roughness (Rq) from 1.28 to 0.15 nm. This reduction is hypothesized to result from the dissolution of elemental Pb by HCl and SiO2 by NaOH. At 2.0 kV, pulse gain increased from 2.00 × 106 to 8.25 × 106, while dark count rate decreased from 54.23 to below 2 counts/s. A nominally 5.5 nm Al2O3 coating deposited by ALD further increased gain fourfold to 3.30 × 107. After an accumulated output charge of 0.158 C, analog gain loss decreased from 89% to 11%. Based on CST Studio Suite 2021, a three-dimensional electromagnetic simulation model of CEM was built. The simulation results show that the pulse full width at half maximum (FWHM) of CEM is 6.4 ns, which is basically consistent with the measured result of 8 ns. Increasing protrusion thickness from 0 to 0.4 mm reduced simulated gain from 8.71 × 106 to 2.60 × 106 at 2.0 kV. The combined experimental and simulation results provide a basis for developing CEMs with improved gain, noise performance and lifetime.
Förderung
- National Natural Science Foundation of China
Zitieren
APA
Hu, Z., Cong, X., Qian, Y., Liu, S., Zhu, J., Zhao, H., Wang, J., Cheng, Y., Niu, P., & Li, L. (2026). Fabrication and Characterization of High-Performance Channel Electron Multipliers Using Alternating Acid and Base Etching and Atomic Layer Deposition. Surfaces, 9(4), 97. https://doi.org/10.3390/surfaces9040097
Vancouver
Hu Z, Cong X, Qian Y, Liu S, Zhu J, Zhao H, et al. Fabrication and Characterization of High-Performance Channel Electron Multipliers Using Alternating Acid and Base Etching and Atomic Layer Deposition. Surfaces. 2026;9(4):97. doi:10.3390/surfaces9040097
BibTeX
@article{Hu2026,
author = {Hu, Zexun and Cong, Xiaoqing and Qian, Yunsheng and Liu, Shulin and Zhu, Jiaqi and Zhao, Heng and Wang, Jian and Cheng, Yan and Niu, Pengjie and Li, Longhui},
title = {Fabrication and Characterization of High-Performance Channel Electron Multipliers Using Alternating Acid and Base Etching and Atomic Layer Deposition},
journal = {Surfaces},
year = {2026},
volume = {9},
number = {4},
pages = {97},
doi = {10.3390/surfaces9040097}
}
EUVIMED