EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Conceptual Electric Bus Body Structure with Battery-Integrated Pillars: Beam-Based Finite Element Modelling and UNECE R66 Rollover Assessment

Kostiantyn Holenko, Oleksandr Dykha, Anna Markiewicz, Anna Piętocha, Ivan Kernytskyy, Orest Horbay, Eugeniusz Koda

Sustainability · 13.05.2026 · 18 (10) · 4885

DOI: 10.3390/su18104885 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sustainability, online erschienen am 13.05.2026. Verfasst von Kostiantyn Holenko und 6 weiteren Autor:innen. Die Arbeit wurde bisher 5-mal zitiert (Crossref) und nennt 40 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The electrification of urban buses under forthcoming Euro 7 regulations requires new structural solutions ensuring both safety and efficient mass distribution. This study proposes a novel conceptual electric bus body structure with battery-integrated inter-window pillars, in which energy storage systems are embedded. The concept was evaluated using finite element analysis in ANSYS under UNECE R66 rollover conditions by comparing an original diesel configuration (O-model) with a battery-integrated electric (B-model) one. Despite a substantial increase in body mass (from 1947 to 5464 kg), the B-model demonstrated improved structural performance. The maximum deformation decreased from 1489.5 to 1319.7 mm, while the difference between the control point displacements decreased from 32.21 to 12.68 mm. The average relative deformation of pillars decreased from 8.48% to 3.59%, and the intrusion amplitude was reduced from approximately 566 to 167 mm. Analysis showed comparable peak von Mises stresses (414.62 MPa vs. 439.19 MPa), but the B-model exhibited a 6.7% reduction in critical regions and a 16.9% decrease in average stress levels. The B-model remained within the elastic regime at the end of the simulation, whereas the O-model showed residual plastic deformation. The results indicate that integrating battery systems into load-bearing pillars leads to improved structural stiffness and deformation behaviour under rollover conditions, while full certification-level verification of UNECE R66 compliance is beyond the scope of the present study.

Zitieren

APA

Holenko, K., Dykha, O., Markiewicz, A., Piętocha, A., Kernytskyy, I., Horbay, O., & Koda, E. (2026). Conceptual Electric Bus Body Structure with Battery-Integrated Pillars: Beam-Based Finite Element Modelling and UNECE R66 Rollover Assessment. Sustainability, 18(10), 4885. https://doi.org/10.3390/su18104885

Vancouver

Holenko K, Dykha O, Markiewicz A, Piętocha A, Kernytskyy I, Horbay O, et al. Conceptual Electric Bus Body Structure with Battery-Integrated Pillars: Beam-Based Finite Element Modelling and UNECE R66 Rollover Assessment. Sustainability. 2026;18(10):4885. doi:10.3390/su18104885

BibTeX
@article{Holenko2026,
  author = {Holenko, Kostiantyn and Dykha, Oleksandr and Markiewicz, Anna and Piętocha, Anna and Kernytskyy, Ivan and Horbay, Orest and Koda, Eugeniusz},
  title = {Conceptual Electric Bus Body Structure with Battery-Integrated Pillars: Beam-Based Finite Element Modelling and UNECE R66 Rollover Assessment},
  journal = {Sustainability},
  year = {2026},
  volume = {18},
  number = {10},
  pages = {4885},
  doi = {10.3390/su18104885}
}
Kostenlos starten →