EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

An Automated Fluorescence Microscopy-Based Sensing System for Continuous Detection of Airborne Asbestos Fibers on a PM2.5 Monitoring Platform

Akio Kuroda, Kenichiro Kaga, Tomoki Nishimura, Kyoka Ichikawa, Shogo Yamazaki, Hisakage Funabashi, Takeshi Ikeda, Takenori Ishida

Sensors · 16.05.2026 · 26 (10) · 3163

DOI: 10.3390/s26103163 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, online erschienen am 16.05.2026. Verfasst von Akio Kuroda und 7 weiteren Autor:innen. Beteiligte Einrichtung: Graduate School of Integrated Sciences for Life, Hiroshima University, 1-3-1 Kagamiyama, Higashi-Hiroshima 739-8530, Hiroshima, Japan. Die Arbeit nennt 23 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Environmental Restoration and Conservation Agency.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Despite regulations restricting asbestos use in many developed countries, asbestos-containing materials (ACMs) persist in aging buildings and can release airborne fibers during demolition and renovation. Therefore, continuous monitoring of airborne asbestos fibers is essential for environmental safety and exposure assessment. Fluorescence microscopy (FM) with fluorescently labeled asbestos-binding proteins offers greater sensitivity and selectivity in detection compared with conventional phase contrast microscopy (PCM). However, its practical application is limited by manual sample preparation and microscopic observations. This study introduces the conceptual design and initial development of an automated FM-based sensing system for monitoring airborne asbestos fibers. The system was constructed by modifying a commercial PM2.5 continuous air sampling platform and integrating automated fluorescent staining, FM imaging, and AI-assisted image analysis for fiber recognition and counting. The system automatically reports airborne asbestos concentrations with corresponding fluorescence images and advances the membrane filter to enable continuous measurements. Performance evaluation using pulverized ACMs showed an overall agreement within 14.1% with PCM–scanning electron microscopy measurements at the group level. Although variability was observed at low fiber concentrations owing to stochastic sampling effects, the results validate the feasibility of automated FM-based sensing for continuous environmental monitoring of airborne asbestos fibers.

Schlagwörter

Stichwörter der Autor:innen

AI-assisted image analysisPM2.5 monitoring platformairborne asbestos sensingautomated monitoringfluorescence microscopy

Autor:innen und Institutionen

  • Graduate School of Integrated Sciences for Life, Hiroshima University, 1-3-1 Kagamiyama, Higashi-Hiroshima 739-8530, Hiroshima, Japan.
  • DKK-TOA Corporation, 613 Kitairiso, Sayama 350-1388, Japan.

Förderung

  • Environmental Restoration and Conservation Agency

Zitieren

APA

Kuroda, A., Kaga, K., Nishimura, T., Ichikawa, K., Yamazaki, S., Funabashi, H., Ikeda, T., & Ishida, T. (2026). An Automated Fluorescence Microscopy-Based Sensing System for Continuous Detection of Airborne Asbestos Fibers on a PM2.5 Monitoring Platform. Sensors, 26(10), 3163. https://doi.org/10.3390/s26103163

Vancouver

Kuroda A, Kaga K, Nishimura T, Ichikawa K, Yamazaki S, Funabashi H, et al. An Automated Fluorescence Microscopy-Based Sensing System for Continuous Detection of Airborne Asbestos Fibers on a PM2.5 Monitoring Platform. Sensors. 2026;26(10):3163. doi:10.3390/s26103163

BibTeX
@article{Kuroda2026,
  author = {Kuroda, Akio and Kaga, Kenichiro and Nishimura, Tomoki and Ichikawa, Kyoka and Yamazaki, Shogo and Funabashi, Hisakage and Ikeda, Takeshi and Ishida, Takenori},
  title = {An Automated Fluorescence Microscopy-Based Sensing System for Continuous Detection of Airborne Asbestos Fibers on a PM2.5 Monitoring Platform},
  journal = {Sensors},
  year = {2026},
  volume = {26},
  number = {10},
  pages = {3163},
  doi = {10.3390/s26103163}
}
Kostenlos starten →