EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Geometrically Optimized FDM-Printed Conductive TPU Bend Sensors for Hand Rehabilitation

Ahmet Özkurt iD, Damla Gürkan Kuntalp iD, Ozan Kayacan iD, Özlem Kayacan iD, Selnur Narin Aral iD

Sensors · 09.04.2026 · 26 (8) · 2309

DOI: 10.3390/s26082309 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, online erschienen am 09.04.2026. Verfasst von Ahmet Özkurt und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Electrical and Electronics Engineering, Dokuz Eylül University, İzmir 35390, Turkey. Hauptthemen laut MEDLINE: Polyurethanes, Hand, Rehabilitation. Die Arbeit wurde bisher 7-mal zitiert (Crossref) und nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Universities Support Program, Dokuz Eylül University.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Flexible resistive bend sensors are essential for monitoring human movement in smart rehabilitation and soft robotics. However, widespread adoption is currently hindered by a trade-off between the high cost of metal-film technologies and the performance degradation (significant hysteresis and non-linearity) of low-cost carbon/polymer composites. This study presents a geometrically customizable bending sensor fabricated from conductive thermoplastic polyurethane (TPU) using Fused Deposition Modeling (FDM) technology as an accessible alternative to commercial sensors. By parametrically optimizing physical dimensions—including trace width, layer thickness, and pattern geometry—the sensors were tailored to achieve target resistance values within a target window of 20–50 kΩ (achieved: ~44 kΩ nominal) for specific finger-joint applications. Electromechanical characterization revealed a negative gauge factor (GF), where resistance decreases upon bending or elongation due to conductive pathway formation and densification within the polymer matrix. This behavior cannot affect sensor operation, and required bend-resistance responses were acquired using geometrical optimization. To compensate for inherent viscoelastic-induced hysteresis and non-linear behavior, a third-degree polynomial modeling approach was implemented. This modeling approach yielded a coefficient of determination (R2) of approximately 0.90. Compared to standard commercial sensors, the proposed FDM-printed design successfully overcomes geometric limitations while offering a cost-effective, high-performance solution for tailor-made wearable technologies and smart rehabilitation gloves.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

PolyurethanesHandRehabilitationHumansElectric ConductivityEquipment DesignRoboticsWearable Electronic Devices

Stichwörter der Autor:innen

3D printingbend sensorconductive TPUnegative gauge factorrehabilitation gloveresistivewearable sensors

Substanzen

Polyurethanes

Autor:innen und Institutionen

  • Department of Electrical and Electronics Engineering, Dokuz Eylül University, İzmir 35390, Turkey.
  • Department of Textile Engineering, Dokuz Eylül University, İzmir 35390, Turkey.
  • Faculty of Physical Therapy and Rehabilitation, Dokuz Eylül University, İzmir 35330, Turkey.

ORCID-Profile: Ahmet Özkurt, Damla Gürkan Kuntalp, Ozan Kayacan, Özlem Kayacan, Selnur Narin Aral

Förderung

  • Universities Support Program
  • Dokuz Eylül University

Zitieren

APA

Özkurt, A., Gürkan Kuntalp, D., Kayacan, O., Kayacan, Ö., & Aral, S. N. (2026). Geometrically Optimized FDM-Printed Conductive TPU Bend Sensors for Hand Rehabilitation. Sensors, 26(8), 2309. https://doi.org/10.3390/s26082309

Vancouver

Özkurt A, Gürkan Kuntalp D, Kayacan O, Kayacan Ö, Aral SN. Geometrically Optimized FDM-Printed Conductive TPU Bend Sensors for Hand Rehabilitation. Sensors. 2026;26(8):2309. doi:10.3390/s26082309

BibTeX
@article{zkurt2026,
  author = {Özkurt, Ahmet and Gürkan Kuntalp, Damla and Kayacan, Ozan and Kayacan, Özlem and Aral, Selnur Narin},
  title = {Geometrically Optimized FDM-Printed Conductive TPU Bend Sensors for Hand Rehabilitation},
  journal = {Sensors},
  year = {2026},
  volume = {26},
  number = {8},
  pages = {2309},
  doi = {10.3390/s26082309}
}
Kostenlos starten →