EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Photopolymerization 3D-Printed Dual-Modal Flexible Sensor for Glucose and pH Monitoring

Shao Lin, Yu Li, Zhenyao Yang, Qiuzheng Li, Bohua Pang, Yin Feng, Jianglin Fu, Guangmeng Ma, Yu Long iD

Sensors · 2025

DOI: 10.3390/s25175358 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, 2025. Verfasst von Shao Lin und 8 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical Engineering, Guangxi University, Nanning 530004, China. Hauptthemen laut MEDLINE: Glucose, Biosensing Techniques, Printing, Three-Dimensional. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Key R&D Program of China, Key R&D Program of Guangxi Province, Internet Information Innovation Talent of Guangxi Province.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Currently, flexible sensors based on electrochemical principles are predominantly limited to single-parameter detection, making it challenging to meet the demand for synchronous monitoring of multiple analytes in complex physiological environments. This study presents a 3D-printed flexible sensor for synchronous glucose/pH detection. Glucose was quantified via H2O2 oxidation current (GOD-catalyzed reaction), while pH was measured through polyaniline (PANI) resistance changes. The ionogel-based microneedle electrode ensures mechanical robustness. At 0.2 V, optimal signal decoupling was achieved: glucose oxidation current dominates, while PANI’s polarization effect is minimized. Neutral pH minimally affected glucose oxidase (GOD) activity, and low glucose concentrations induced negligible pH interference, ensuring orthogonality. In artificial interstitial fluid, the sensor showed glucose: linear response (0.5–2.5 g·L−1, 0.288 μA·mM−1·cm−2); pH: piecewise-linear sensitivity (0.155 Ω/pH·cm2 for pH > 7; 0.135 Ω/pH·cm2 for pH < 7). The design enables real-time multiparameter monitoring with high selectivity, addressing current limitations in flexible electrochemical sensors.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

GlucoseBiosensing TechniquesPrinting, Three-DimensionalHydrogen-Ion ConcentrationGlucose OxidaseHydrogen PeroxideElectrochemical TechniquesAniline CompoundsElectrodesPolymerizationOxidation-Reduction

Stichwörter der Autor:innen

biosensorsflexible materialsglucose sensingpH sensing

Substanzen

GlucoseGlucose OxidasepolyanilineHydrogen PeroxideAniline Compounds

Autor:innen und Institutionen

  • School of Mechanical Engineering, Guangxi University, Nanning 530004, China.
  • School of Resources, Environment and Materials, Guangxi University, Nanning 530004, China.

ORCID-Profile: Yu Long

Förderung

  • National Key R&amp;D Program of China
  • Key R&amp;D Program of Guangxi Province
  • Internet Information Innovation Talent of Guangxi Province

Zitieren

APA

Lin, S., Li, Y., Yang, Z., Li, Q., Pang, B., Feng, Y., Fu, J., Ma, G., & Long, Y. (2025). Photopolymerization 3D-Printed Dual-Modal Flexible Sensor for Glucose and pH Monitoring. Sensors. https://doi.org/10.3390/s25175358

Vancouver

Lin S, Li Y, Yang Z, Li Q, Pang B, Feng Y, et al. Photopolymerization 3D-Printed Dual-Modal Flexible Sensor for Glucose and pH Monitoring. Sensors. 2025. doi:10.3390/s25175358

BibTeX
@article{Lin2025,
  author = {Lin, Shao and Li, Yu and Yang, Zhenyao and Li, Qiuzheng and Pang, Bohua and Feng, Yin and Fu, Jianglin and Ma, Guangmeng and Long, Yu},
  title = {Photopolymerization 3D-Printed Dual-Modal Flexible Sensor for Glucose and pH Monitoring},
  journal = {Sensors},
  year = {2025},
  doi = {10.3390/s25175358}
}
Kostenlos starten →