EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Adaptive Fabrication of Electrochemical Chips with a Paste-Dispensing 3D Printer

Ten It Wong iD, Candy Ng, Shengxuan Lin, Zhong Chen iD, Xiaodong Zhou iD

Sensors · 29.04.2024 · 24 (9) · 2844

DOI: 10.3390/s24092844 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, online erschienen am 29.04.2024. Verfasst von Ten It Wong und 4 weiteren Autor:innen. Beteiligte Einrichtung: Institute of Materials Research and Engineering, A*STAR (Agency for Science, Technology and Research), 2 Fusionopolis Way, #08-03, Innovis, Singapore…. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 56 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Environment Agency, National Environment Agency of Singapore.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Electrochemical (EC) detection is a powerful tool supporting simple, low-cost, and rapid analysis. Although screen printing is commonly used to mass fabricate disposable EC chips, its mask is relatively expensive. In this research, we demonstrated a method for fabricating three-electrode EC chips using 3D printing of relatively high-viscosity paste. The electrodes consisted of two layers, with carbon paste printed over silver/silver chloride paste, and the printed EC chips were baked at 70 °C for 1 h. Engineering challenges such as bulging of the tubing, clogging of the nozzle, dripping, and local accumulation of paste were solved by material selection for the tube and nozzle, and process optimization in 3D printing. The EC chips demonstrated good reversibility in redox reactions through cyclic voltammetry tests, and reliably detected heavy metal ions Pb(II) and Cd(II) in solutions using differential pulse anodic stripping voltammetry measurements. The results indicate that by optimizing the 3D printing of paste, EC chips can be obtained by maskless and flexible 3D printing techniques in lieu of screen printing.

Schlagwörter

Stichwörter der Autor:innen

3D printingadditive manufacturedisposable EC chipelectrochemical (EC)sensing

Autor:innen und Institutionen

  • Institute of Materials Research and Engineering, A*STAR (Agency for Science, Technology and Research), 2 Fusionopolis Way, #08-03, Innovis, Singapore 138634, Singapore.
  • School of Materials Science & Engineering, Nanyang Technological University, Block N4.1, Nanyang Avenue, Singapore 639798, Singapore.
  • Residues and Resource Reclamation Centre (R3C), Nanyang Environment and Water Research Institute, Nanyang Technological University, 1 Cleantech Loop, Clean Tech One, Singapore 637141, Singapore.

ORCID-Profile: Ten It Wong, Zhong Chen, Xiaodong Zhou

Förderung

  • National Environment Agency
  • National Environment Agency of Singapore

Zitieren

APA

Wong, T. I., Ng, C., Lin, S., Chen, Z., & Zhou, X. (2024). Adaptive Fabrication of Electrochemical Chips with a Paste-Dispensing 3D Printer. Sensors, 24(9), 2844. https://doi.org/10.3390/s24092844

Vancouver

Wong TI, Ng C, Lin S, Chen Z, Zhou X. Adaptive Fabrication of Electrochemical Chips with a Paste-Dispensing 3D Printer. Sensors. 2024;24(9):2844. doi:10.3390/s24092844

BibTeX
@article{Wong2024,
  author = {Wong, Ten It and Ng, Candy and Lin, Shengxuan and Chen, Zhong and Zhou, Xiaodong},
  title = {Adaptive Fabrication of Electrochemical Chips with a Paste-Dispensing 3D Printer},
  journal = {Sensors},
  year = {2024},
  volume = {24},
  number = {9},
  pages = {2844},
  doi = {10.3390/s24092844}
}
Kostenlos starten →