EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Modeling, Fabrication, and Testing of a 3D-Printed Coriolis Mass Flow Sensor

Mahdieh Yariesbouei, Remco G P Sanders, Remco J Wiegerink iD, Joost C Lötters

Sensors · 18.04.2023 · 23 (8) · 4062

DOI: 10.3390/s23084062 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Sensors, online erschienen am 18.04.2023. Verfasst von Mahdieh Yariesbouei und 3 weiteren Autor:innen. Beteiligte Einrichtung: Integrated Devices and Systems, University of Twente, 7500 AE Enschede, The Netherlands. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Bronkhorst High-Tech BV, Topconsortium voor Kennis en Innovatie Hightech Systemen & Materialen, Topconsortium voor Kennis en Innovatie Hightech Systemen & Materialen.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This paper presents the modeling, fabrication, and testing of a 3D-printed Coriolis mass flow sensor. The sensor contains a free-standing tube with a circular cross-section printed using the LCD 3D-printing technique. The tube has a total length of 42 mm, an inner diameter of about 900 µm, and a wall thickness of approximately 230 µm. The outer surface of the tube is metalized using a Cu plating process, resulting in a low electrical resistance of 0.5 Ω. The tube is brought into vibration using an AC current in combination with a magnetic field from a permanent magnet. The displacement of the tube is detected using a laser Doppler vibrometer (LDV) that is part of a Polytec MSA-600 microsystem analyzer. The Coriolis mass flow sensor has been tested over a flow range of 0–150 g/h for water, 0–38 g/h for isopropyl alcohol (IPA), and 0–50 g/h for nitrogen. The maximum flow rates of water and IPA resulted in less than a 30 mbar pressure drop. The pressure drop at the maximum flow rate of nitrogen is 250 mbar.

Schlagwörter

Stichwörter der Autor:innen

3D-printed tubeCoriolis mass flow sensorcircular cross-section

Autor:innen und Institutionen

  • Integrated Devices and Systems, University of Twente, 7500 AE Enschede, The Netherlands.
  • Bronkhorst High-Tech BV, 7261 AK Ruurlo, The Netherlands.

ORCID-Profile: Remco J Wiegerink

Förderung

  • Bronkhorst High-Tech BV
  • Topconsortium voor Kennis en Innovatie Hightech Systemen & Materialen
  • Topconsortium voor Kennis en Innovatie Hightech Systemen & Materialen

Zitieren

APA

Yariesbouei, M., Sanders, R. G. P., Wiegerink, R. J., & Lötters, J. C. (2023). Modeling, Fabrication, and Testing of a 3D-Printed Coriolis Mass Flow Sensor. Sensors, 23(8), 4062. https://doi.org/10.3390/s23084062

Vancouver

Yariesbouei M, Sanders RGP, Wiegerink RJ, Lötters JC. Modeling, Fabrication, and Testing of a 3D-Printed Coriolis Mass Flow Sensor. Sensors. 2023;23(8):4062. doi:10.3390/s23084062

BibTeX
@article{Yariesbouei2023,
  author = {Yariesbouei, Mahdieh and Sanders, Remco G P and Wiegerink, Remco J and Lötters, Joost C},
  title = {Modeling, Fabrication, and Testing of a 3D-Printed Coriolis Mass Flow Sensor},
  journal = {Sensors},
  year = {2023},
  volume = {23},
  number = {8},
  pages = {4062},
  doi = {10.3390/s23084062}
}
Kostenlos starten →