EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Particle Size Distribution Characteristics of Drilled Cuttings During Horizontal Section Drilling in Coal-Rock Gas Wells

Yanlong Zhang, Gensheng Li, Meng Cui, Hua Wu, Xiaoqiong Wang

Processes · 24.06.2026 · 14 (13) · 2049

DOI: 10.3390/pr14132049 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Processes, online erschienen am 24.06.2026. Verfasst von Yanlong Zhang und 4 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Science and Technology Major Project, CNPC Science and Technology Special Project, Open Fund of State Key Laboratory for Fine Exploration and Intelligent Development of Coal Resources.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

During horizontal drilling in coal-rock gas reservoirs, the particle size distribution (PSD) of drilled cuttings directly affects drilling efficiency, hole cleaning, and wellbore stability. However, the evolution of cuttings PSD and its controlling mechanisms during coal-rock fragmentation remain insufficiently understood. In this study, a drill bit–coal-rock interaction model was established using the discrete element method (DEM) and calibrated against uniaxial compression experiments. The effects of weight on bit (WOB), rotational speed, and depth of cut (DOC) on cuttings PSD were quantitatively investigated. The results show that the relative influence on the maximum cutting size followed the order of DOC > WOB > rotational speed, whereas the influence on the average cutting size followed the order of rotational speed > WOB > DOC. Increasing DOC from 0.5 mm to 1.5 mm increased the maximum cutting size from 11.6 mm to 29.4 mm. Increasing WOB promoted the generation of medium- and large-sized cuttings, thereby increasing hole-cleaning requirements. Meanwhile, increasing rotational speed from 40 rpm to 90 rpm reduced the average cutting size and shifted the dominant cutting fraction from 4–6 mm to 1–4 mm. DEM observations reveal that cutting PSD evolution is jointly controlled by primary brittle fracture and secondary particle breakage through a five-stage fragmentation process involving stress concentration, microcrack initiation, crack propagation and coalescence, fragment detachment, and secondary fragmentation. Field validation using 146 cutting samples demonstrated the applicability of the proposed optimization strategy. Under the investigated drilling conditions, a DOC of approximately 0.5 mm and a rotational speed of 70–90 rpm were found to effectively limit oversized cutting generation. These findings improve the mechanistic understanding of cutting PSD evolution and provide practical guidance for drilling parameter optimization and hole-cleaning management in coal-rock gas horizontal wells.

Förderung

  • National Science and Technology Major Project
  • CNPC Science and Technology Special Project
  • Open Fund of State Key Laboratory for Fine Exploration and Intelligent Development of Coal Resources

Zitieren

APA

Zhang, Y., Li, G., Cui, M., Wu, H., & Wang, X. (2026). Particle Size Distribution Characteristics of Drilled Cuttings During Horizontal Section Drilling in Coal-Rock Gas Wells. Processes, 14(13), 2049. https://doi.org/10.3390/pr14132049

Vancouver

Zhang Y, Li G, Cui M, Wu H, Wang X. Particle Size Distribution Characteristics of Drilled Cuttings During Horizontal Section Drilling in Coal-Rock Gas Wells. Processes. 2026;14(13):2049. doi:10.3390/pr14132049

BibTeX
@article{Zhang2026,
  author = {Zhang, Yanlong and Li, Gensheng and Cui, Meng and Wu, Hua and Wang, Xiaoqiong},
  title = {Particle Size Distribution Characteristics of Drilled Cuttings During Horizontal Section Drilling in Coal-Rock Gas Wells},
  journal = {Processes},
  year = {2026},
  volume = {14},
  number = {13},
  pages = {2049},
  doi = {10.3390/pr14132049}
}
Kostenlos starten →