EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Multi-Objective Optimization of Injection Molding Process Parameters for Moderately Thick Plane Lens Based on PSO-BPNN, OMOPSO, and TOPSIS

Feng Liu, Jianjun Pang, Zhiwei Xu

Processes · 22.12.2023 · 12 (1) · 36

DOI: 10.3390/pr12010036 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Processes, online erschienen am 22.12.2023. Verfasst von Feng Liu und 2 weiteren Autor:innen. Die Arbeit wurde bisher 15-mal zitiert (Crossref) und nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Zhejiang Provincial Natural Science Foundation of China, State Key Laboratory of Materials Processing and Die & Mould Technology, Huazhong University of Science and Technology, Key Laboratory for Technology in Rural Water Management of Zhejiang Province.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Injection molding (IM) is an ideal technique for the low-cost mass production of moderately thick plane lenses (MTPLs). However, the optical performance of injection molded MTPL is seriously degraded by the warpage and sink marks induced during the molding process with complex historical thermal field changes. Thus, it is essential that the processing parameters utilized in the molding process are properly assigned. And the challenges are further compounded when considering the MTPL molding energy consumption. This paper presents a set of procedures for the optimization of injection molding process parameters, with warpage, sink marks reflecting the optical performance, and clamping force reflecting the molding energy consumption as the optimization objectives. First, the orthogonal experiment was carried out with the Taguchi method, and the S/N response shows that these three objectives cannot reach the optimal values simultaneously. Second, considering the experimental data scale, the back propagation neural network updated by the particle swarm optimization method (PSO-BPNN) was applied to establish the complex nonlinear mapping relationship between the process parameters and these three trade-off objectives respectively. Then, the Pareto optimal frontier of the multi-objective optimization problem was attained by multi-objective particle swarm optimization using a mutation operator and dominance coefficient algorithm (OMOPSO). And the competitive relationship between these objectives was further confirmed by the corresponding pairwise Pareto frontiers. Additionally, the TOPSIS method with equal weights was employed to achieve the best optimal solution from the Pareto optimal frontier. The simulation results yielded that the maximum values of warpage, sink marks, and clamping force could be reduced by 7.44%, 40.56%, and 5.56%, respectively, after optimization. Finally, MTPL products were successfully fabricated.

Förderung

  • Zhejiang Provincial Natural Science Foundation of China
  • State Key Laboratory of Materials Processing and Die & Mould Technology, Huazhong University of Science and Technology
  • Key Laboratory for Technology in Rural Water Management of Zhejiang Province
  • Domestic Visiting Scholar Program for Higher Education Institutions of China
  • Zhejiang University of Water Resources and Electric Power

Zitieren

APA

Liu, F., Pang, J., & Xu, Z. (2023). Multi-Objective Optimization of Injection Molding Process Parameters for Moderately Thick Plane Lens Based on PSO-BPNN, OMOPSO, and TOPSIS. Processes, 12(1), 36. https://doi.org/10.3390/pr12010036

Vancouver

Liu F, Pang J, Xu Z. Multi-Objective Optimization of Injection Molding Process Parameters for Moderately Thick Plane Lens Based on PSO-BPNN, OMOPSO, and TOPSIS. Processes. 2023;12(1):36. doi:10.3390/pr12010036

BibTeX
@article{Liu2023,
  author = {Liu, Feng and Pang, Jianjun and Xu, Zhiwei},
  title = {Multi-Objective Optimization of Injection Molding Process Parameters for Moderately Thick Plane Lens Based on PSO-BPNN, OMOPSO, and TOPSIS},
  journal = {Processes},
  year = {2023},
  volume = {12},
  number = {1},
  pages = {36},
  doi = {10.3390/pr12010036}
}
Kostenlos starten →