EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comparative Evaluation of the Mechanical Properties of an Alkasite-Based Material and a Conventional Resin Composite

Selma Jakupović iD, Damir Duratbegović iD, Nedim Pervan iD, Enis Muratović iD, Vedran Jakupović iD

Polymers · 08.11.2026 · 18 (21) · 2788

DOI: 10.3390/polym18212788 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 08.11.2026. Verfasst von Selma Jakupović und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Dentistry and Endodontics, Faculty of Dentistrywith Dental Clinical Center, University of Sarajevo, 71000 Sarajevo, Bosnia …. Die Arbeit nennt 52 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Federalno Ministarstvo Obrazovanja i Nauke, Federal Ministry of Education and Science.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Alkasites are resin-based restorative materials that differ from conventional resin composites in the composition and reactivity of their filler system, which enables ion release. Whether optional light activation changes the mechanical properties of the alkasite Cention Forte, compared with self-curing and with a conventional composite, remains insufficiently documented. This in vitro study compared Cention Forte (urethane dimethacrylate-based matrix; reactive calcium fluorosilicate and barium glass fillers) in self-cured (G1) and light-cured (G2) modes with the nanohybrid composite Tetric EvoCeram (G0; dimethacrylate matrix; barium glass, ytterbium trifluoride, mixed oxide and prepolymerized fillers). Top- and bottom-surface Vickers microhardness (VMHt, VMHb), bottom-to-top ratio (BTR), diametral tensile strength (DTS) and compressive strength (CS) were measured (n = 7). G1 showed the highest VMHt (70.3 HV), followed by G0 (63.0 HV) and G2 (57.8 HV) (p< 0.001). Both Cention Forte groups had BTR values of approximately 1.00 (G0: 0.97) as an indirect, surface-based index. G2 exhibited the highest DTS (39.7 MPa) and G0 the highest CS (311.2 MPa). Curing mode accounted for most between-group variance in microhardness, whereas material composition dominated compressive strength.

Schlagwörter

Stichwörter der Autor:innen

Cention ForteVickers microhardnessalkasitebottom-to-top ratiocompressive strengthcuring modediametral tensile strengthfiller contentresin composite

Autor:innen und Institutionen

  • Department of Restorative Dentistry and Endodontics, Faculty of Dentistrywith Dental Clinical Center, University of Sarajevo, 71000 Sarajevo, Bosnia and Herzegovina.
  • Department of Pediatric and Preventive Dentistry, Faculty of Dentistry with Dental Clinical Center, University of Sarajevo, 71000 Sarajevo, Bosnia and Herzegovina.
  • Department of Mechanical Design, Faculty of Mechanical Engineering, University of Sarajevo, 71000 Sarajevo, Bosnia and Herzegovina.
  • Department of Community Healthcare, Faculty of Health Studies, University of Sarajevo, 71000 Sarajevo, Bosnia and Herzegovina.

ORCID-Profile: Selma Jakupović, Damir Duratbegović, Nedim Pervan, Enis Muratović, Vedran Jakupović

Förderung

  • Federalno Ministarstvo Obrazovanja i Nauke
  • Federal Ministry of Education and Science

Zitieren

APA

Jakupović, S., Duratbegović, D., Pervan, N., Muratović, E., & Jakupović, V. (2026). Comparative Evaluation of the Mechanical Properties of an Alkasite-Based Material and a Conventional Resin Composite. Polymers, 18(21), 2788. https://doi.org/10.3390/polym18212788

Vancouver

Jakupović S, Duratbegović D, Pervan N, Muratović E, Jakupović V. Comparative Evaluation of the Mechanical Properties of an Alkasite-Based Material and a Conventional Resin Composite. Polymers. 2026;18(21):2788. doi:10.3390/polym18212788

BibTeX
@article{Jakupovi2026,
  author = {Jakupović, Selma and Duratbegović, Damir and Pervan, Nedim and Muratović, Enis and Jakupović, Vedran},
  title = {Comparative Evaluation of the Mechanical Properties of an Alkasite-Based Material and a Conventional Resin Composite},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {21},
  pages = {2788},
  doi = {10.3390/polym18212788}
}
Kostenlos starten →