EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Annealing on the Mechanical Properties of Carbon Fiber-Reinforced PLA

Daniel Perez-Solis iD, Jose Martinez-Trinidad iD, Alvaro Frutos iD, Manuel Coca-Gonzalez iD, Moises Jimenez-Martinez iD

Polymers · 02.11.2026 · 18 (21) · 2721

DOI: 10.3390/polym18212721 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 02.11.2026. Verfasst von Daniel Perez-Solis und 4 weiteren Autor:innen. Beteiligte Einrichtung: Grupo Ingeniería de Superficies, ESIME Zacatenco, Instituto Politecnico Nacional, Mexico City C.P. 07738, Mexico. Die Arbeit nennt 65 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Tecnologico de Monterrey for the Article Processing Charge.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additive manufacturing of polylactic acid reinforced with carbon fiber, specifically via fused deposition modeling, offers significant advantages for fabricating complex geometries; however, inherent extrusion defects often restrict its use in high-performance mechanical components. While post-printing annealing treatments promote polymer crystallization and interlayer cohesion, the highly non-linear effects of this process on PLA composites remain underexplored. This study investigates the specific effects of annealing temperature and exposure time on parametrically optimized 3D-printed polylactic acid reinforced with short carbon fiber. An orthogonal experimental design evaluates temperatures ranging from 55 °C to 95 °C and times between 4 and 12 h. The mechanical behavior was mapped utilizing Analysis of Variance and Response Surface Methodology, supported by Differential Scanning Calorimetry and dimensional analysis. The results revealed that annealing temperature is the governing factor, whereas exposure time has a marginal impact. An optimal window emerged between 75 °C and 85 °C. Relative to the as-printed baseline, optimal factors improved Ultimate Tensile Strength by 13.74%, ductility by 24.78%, bed surface hardness by 5.58% and Young’s modulus by 39%, driven by substantial matrix crystallinity increments (29.4%) verified via DSC. In contrast, top surface hardness was negatively affected by the heat treatment. Furthermore, temperatures exceeding 85 °C triggered severe dimensional distortions. Ultimately, this research provides experimentally validated statistical models for the reliable design of PLA-SCF components.

Schlagwörter

Stichwörter der Autor:innen

3D printingResponse Surface Methodologyannealingmechanical properties

Autor:innen und Institutionen

  • Grupo Ingeniería de Superficies, ESIME Zacatenco, Instituto Politecnico Nacional, Mexico City C.P. 07738, Mexico.
  • Kautex Textron de Mexico, S. de R.L. de C.V. Autop., Heroica Puebla de Zaragoza C.P. 72761, Mexico.
  • School of Engineering and Sciences, Tecnologico de Monterrey, Via Atlixcayotl 5718, Puebla C.P. 72453, Mexico.

ORCID-Profile: Daniel Perez-Solis, Jose Martinez-Trinidad, Alvaro Frutos, Manuel Coca-Gonzalez, Moises Jimenez-Martinez

Förderung

  • Tecnologico de Monterrey for the Article Processing Charge

Zitieren

APA

Perez-Solis, D., Martinez-Trinidad, J., Frutos, A., Coca-Gonzalez, M., & Jimenez-Martinez, M. (2026). Effect of Annealing on the Mechanical Properties of Carbon Fiber-Reinforced PLA. Polymers, 18(21), 2721. https://doi.org/10.3390/polym18212721

Vancouver

Perez-Solis D, Martinez-Trinidad J, Frutos A, Coca-Gonzalez M, Jimenez-Martinez M. Effect of Annealing on the Mechanical Properties of Carbon Fiber-Reinforced PLA. Polymers. 2026;18(21):2721. doi:10.3390/polym18212721

BibTeX
@article{PerezSolis2026,
  author = {Perez-Solis, Daniel and Martinez-Trinidad, Jose and Frutos, Alvaro and Coca-Gonzalez, Manuel and Jimenez-Martinez, Moises},
  title = {Effect of Annealing on the Mechanical Properties of Carbon Fiber-Reinforced PLA},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {21},
  pages = {2721},
  doi = {10.3390/polym18212721}
}
Kostenlos starten →