EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Compressive Deformation, Damage Evolution, and Energy Absorption of 3D-Printed PLA and Short-Carbon-Fiber-Reinforced PLA Auxetic Metamaterials

Lan Luo iD, Shidian Qiu, Maokai Li, Lianchao Wang iD, Zhengxian Liu

Polymers · 06.09.2026 · 18 (17) · 2173

DOI: 10.3390/polym18172173 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 06.09.2026. Verfasst von Lan Luo und 4 weiteren Autor:innen. Beteiligte Einrichtung: National Key Laboratory of Science and Technology on Advanced Composites in Special Environments, Harbin Institute of Technology (HIT), Harbin 150080…. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Natural Science Foundation of Heilongjiang Province, National Postdoctoral Program for Innovative Talents.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Auxetic mechanical metamaterials convert axial compression into lateral contraction, providing deformation modes that are attractive for lightweight energy absorbers. Here, fused deposition modeling was used to fabricate polylactic acid (PLA) and 10 wt% short-carbon-fiber-reinforced PLA (CF/PLA) auxetic metamaterials with arrow, re-entrant hexagonal, star-shaped, and chiral rotating topologies. Thermal analysis, tensile testing, and three-point bending first established the effect of carbon-fiber addition on the printable matrix. Quasi-static compression experiments were then combined with finite-element simulations using pressure-dependent plasticity and ductile damage to resolve topology-dependent collapse and energy partition. Adding 10 wt% short carbon fibers increased the tensile modulus from 2.33 to 3.72 GPa and raised the plateau stresses of the auxetic structures by about 50%. The star-shaped CF/PLA metamaterial showed the highest specific energy absorption (approximately 4.7 J/g), whereas the chiral rotating topology showed the largest relative improvement, exceeding 130%. Fiber reinforcement improved stiffness and load transfer but promoted stress localization at hinges, re-entrant corners, and ligament junctions. These findings elucidate the material–topology trade-off between stiffness enhancement and localized embrittlement, offering practical guidelines for designing crashworthy 3D-printed composite metamaterials.

Schlagwörter

Stichwörter der Autor:innen

auxetic metamaterialenergy absorptionfused deposition modelingpolylactic acidshort-carbon-fiber composite

Autor:innen und Institutionen

  • National Key Laboratory of Science and Technology on Advanced Composites in Special Environments, Harbin Institute of Technology (HIT), Harbin 150080, China.
  • Guangzhou Future Additive Manufacturing Research Institute, Guangzhou 510150, China.
  • Department of Materials Science, Polytechnic University of Madrid, 28040 Madrid, Spain.

ORCID-Profile: Lan Luo, Lianchao Wang

Förderung

  • National Natural Science Foundation of China
  • Natural Science Foundation of Heilongjiang Province
  • National Postdoctoral Program for Innovative Talents

Zitieren

APA

Luo, L., Qiu, S., Li, M., Wang, L., & Liu, Z. (2026). Compressive Deformation, Damage Evolution, and Energy Absorption of 3D-Printed PLA and Short-Carbon-Fiber-Reinforced PLA Auxetic Metamaterials. Polymers, 18(17), 2173. https://doi.org/10.3390/polym18172173

Vancouver

Luo L, Qiu S, Li M, Wang L, Liu Z. Compressive Deformation, Damage Evolution, and Energy Absorption of 3D-Printed PLA and Short-Carbon-Fiber-Reinforced PLA Auxetic Metamaterials. Polymers. 2026;18(17):2173. doi:10.3390/polym18172173

BibTeX
@article{Luo2026,
  author = {Luo, Lan and Qiu, Shidian and Li, Maokai and Wang, Lianchao and Liu, Zhengxian},
  title = {Compressive Deformation, Damage Evolution, and Energy Absorption of 3D-Printed PLA and Short-Carbon-Fiber-Reinforced PLA Auxetic Metamaterials},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {17},
  pages = {2173},
  doi = {10.3390/polym18172173}
}
Kostenlos starten →