EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Effect of Cooling Time on Demoulding Temperature, Shrinkage and Warpage of Injection-Moulded Polypropylene Parts

Jan Kleinsorge iD, Yannick Luca Ollig-Gaul, Christian Hopmann iD

Polymers · 29.07.2026 · 18 (15) · 1852

DOI: 10.3390/polym18151852 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 29.07.2026. Verfasst von Jan Kleinsorge und 2 weiteren Autor:innen. Beteiligte Einrichtung: Institute for Plastics Processing (IKV) in Industry and Craft, RWTH Aachen University, Seffenter Weg 201, 52074 Aachen, Germany. Die Arbeit nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In injection moulding, the cooling phase occupies 60–80% of the cycle time, making it the dominant factor for cost-effectiveness and a key driver of dimensional accuracy. Most previous work identified process windows that minimise warpage by simulation, indirectly inferring cooling time. This study experimentally quantifies the effect of cooling time on demoulding temperature and the resulting dimensional deviations. Housing parts were moulded from virgin and post-consumer recycled (PCR) polypropylene (PP). For PCR, a 33 full-factorial design varied cooling time, cylinder temperature and mould temperature. Data were analysed by analysis of variance (ANOVA). For virgin PP, a nine-level design examined cooling time in finer detail. ANOVA revealed R2CT of 0.54 for the effect of cooling time on demoulding temperature, identifying cooling time as the principal factor. For dimensional accuracy, the mould temperature showed the strongest effect (R2MT = 0.44), while cooling-time changes from 0 s to 4 s showed a comparable effect (R2CT = 0.36). For virgin PP, both the demoulding temperature and dimensional deviations decreased at a diminishing rate with increasing cooling time. Thus, a targeted adjustment of the cooling time in short time intervals leads to a significant improvement in dimensional accuracy without substantially compromising cost-effectiveness.

Schlagwörter

Stichwörter der Autor:innen

cooling timeinjection mouldingpolypropylenepost-consumer recycled materialprocess optimisationwarpage

Autor:innen und Institutionen

  • Institute for Plastics Processing (IKV) in Industry and Craft, RWTH Aachen University, Seffenter Weg 201, 52074 Aachen, Germany.

ORCID-Profile: Jan Kleinsorge, Christian Hopmann

Zitieren

APA

Kleinsorge, J., Ollig-Gaul, Y. L., & Hopmann, C. (2026). Effect of Cooling Time on Demoulding Temperature, Shrinkage and Warpage of Injection-Moulded Polypropylene Parts. Polymers, 18(15), 1852. https://doi.org/10.3390/polym18151852

Vancouver

Kleinsorge J, Ollig-Gaul YL, Hopmann C. Effect of Cooling Time on Demoulding Temperature, Shrinkage and Warpage of Injection-Moulded Polypropylene Parts. Polymers. 2026;18(15):1852. doi:10.3390/polym18151852

BibTeX
@article{Kleinsorge2026,
  author = {Kleinsorge, Jan and Ollig-Gaul, Yannick Luca and Hopmann, Christian},
  title = {Effect of Cooling Time on Demoulding Temperature, Shrinkage and Warpage of Injection-Moulded Polypropylene Parts},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {15},
  pages = {1852},
  doi = {10.3390/polym18151852}
}
Kostenlos starten →