Numerical Investigation of Shrinkage and Warpage in a Large Talc-Filled Polypropylene Injection-Molded Component
Materials · 13.11.2026 · 19 (22) · 4828
DOI: 10.3390/ma19224828 ↗Kurz gefasst
Fachartikel in der Zeitschrift Materials, online erschienen am 13.11.2026. Verfasst von Jozef Mikita und 4 weiteren Autor:innen. Die Arbeit nennt 26 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Ministry of Education, Research, Development and Youth of the Slovak Republic.
Abstract (Originalsprache)
This paper presents a numerical analysis of the filling and packing processes, cooling behavior, shrinkage, and warpage in a large-scale injection-molded component produced from polypropylene filled with 40% talc. Simulations were conducted using Autodesk Moldflow Insight 2021 to evaluate process behavior and identify potential dimensional quality issues during injection molding. The simulation model encompassed the filling, packing, and cooling phases, as well as the resulting warpage of the molded part. The Moldflow report listed a fill time of 3.18 s and a filling pressure requirement of approximately 62 MPa under the selected processing conditions. The predicted volumetric shrinkage ranged from 0.20% to 12.65%, and local areas with an elevated risk of sink marks, air traps, and weld lines were identified. The cooling analysis showed localized regions of elevated cycle-averaged temperature on the mold side of the part–mold interface as well as regions with longer predicted times until the specified polymer ejection temperature was reached. The maximum predicted warpage reached 2.60 mm. Dimensional measurements showed that all evaluated dimensions were within the prescribed tolerances in the measured production batch, although preliminary process-capability indices varied among the monitored characteristics, with several values below the specified acceptance criterion of Cpk > 1.67, including values below 1.0. Optical 3D scanning provided complementary experimental information on the geometric deviations of the manufactured parts; a quantitative validation of the Moldflow warpage predictions was not possible with the available data. The numerical analysis employed a substitute Moldflow database material model because a complete material model for the actual production grade was unavailable. Therefore, the quantitative transfer of the predicted shrinkage and warpage values to the production material has not been established. The simulation results provide preliminary spatial guidance for assessing the mold configuration, whereas quantitative shrinkage and warpage predictions require reassessment using a material model based on experimentally determined data for the actual production grade.
Förderung
- Ministry of Education, Research, Development and Youth of the Slovak Republic
Zitieren
APA
Mikita, J., Baron, P., Maščenik, J., Manduľák, D., & Manduľák, J. (2026). Numerical Investigation of Shrinkage and Warpage in a Large Talc-Filled Polypropylene Injection-Molded Component. Materials, 19(22), 4828. https://doi.org/10.3390/ma19224828
Vancouver
Mikita J, Baron P, Maščenik J, Manduľák D, Manduľák J. Numerical Investigation of Shrinkage and Warpage in a Large Talc-Filled Polypropylene Injection-Molded Component. Materials. 2026;19(22):4828. doi:10.3390/ma19224828
BibTeX
@article{Mikita2026,
author = {Mikita, Jozef and Baron, Petr and Maščenik, Jozef and Manduľák, Dušan and Manduľák, Ján},
title = {Numerical Investigation of Shrinkage and Warpage in a Large Talc-Filled Polypropylene Injection-Molded Component},
journal = {Materials},
year = {2026},
volume = {19},
number = {22},
pages = {4828},
doi = {10.3390/ma19224828}
}
EUVIMED