Effects of Acidic Exposure on Surface Properties and Bacterial Adhesion of Three Resin-Based CAD/CAM Materials
Polymers · 25.07.2026 · 18 (15) · 1818
DOI: 10.3390/polym18151818 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 25.07.2026. Verfasst von Sarah Almuhayya und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Clinical Laboratory Science, College of Applied Medical Sciences, King Saud University, Riyadh 12372, Saudi Arabia. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).
Abstract (Originalsprache)
CAD/CAM reinforced resin composites are increasingly used in restorative dentistry because of their favorable mechanical and esthetic properties. This in vitro study evaluated the effect of acidic exposure on surface properties and Streptococcus mutans biofilm formation on three CAD/CAM resin composites: a short-fiber-reinforced composite (SFRC), a woven glass fiber-reinforced composite (TRINIA; TR), and a resin nanoceramic-reinforced composite (Lava Ultimate; LU). Twenty-four specimens from each material were prepared and assessed for surface roughness and wettability using an optical profilometer and contact angle goniometer before and after 24 h of storage in neutral (pH 7) or acidic (pH 4) buffer solutions (n = 12 per group). Surface morphology was further examined using scanning electron microscopy (SEM). Biofilm formation was quantified using S. mutans colony-forming unit (CFU) counts, followed by confocal laser scanning microscopy (CLSM) for biofilm architecture and viability. At baseline, TR exhibited the highest roughness values (0.744 to 0.785 µm, p < 0.001), whereas no significant differences in contact angle were observed among materials. Acidic exposure significantly increased surface roughness and reduced contact angle values in all examined materials (p < 0.001). Compared to storage in neutral conditions, bacterial adhesion was significantly reduced in TR and LU stored in acid (p < 0.001), but SFRC showed no significant change (p = 0.079). Among specimens exposed to acidic conditions, TR exhibited the highest bacterial adhesion (3.24 log10 CFU/mm2) relative to SFRC and LU (p < 0.001). CLSM analysis demonstrated denser biofilm accumulation on TR and LU compared with SFRC. These findings demonstrate that acidic exposure significantly affects the surface properties and bacterial adhesion behavior of CAD/CAM resin composites in a material-dependent manner. SFRC showed no statistically significant difference in S. mutans CFU/mm2 between neutral and acidic storage conditions despite measurable surface changes, highlighting its potential suitability for clinical applications associated with acidic oral environments.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Clinical Laboratory Science, College of Applied Medical Sciences, King Saud University, Riyadh 12372, Saudi Arabia.
- Department of Prosthetic Dental Sciences, College of Dentistry, King Saud University, Riyadh 11545, Saudi Arabia.
- Department of Biomaterials Science and Turku Clinical Biomaterial Center-TCBC, Institute of Dentistry, University of Turku, 20014 Turku, Finland.
- Research Development and Production Department, Stick Tech Ltd.-A GC Europa AG Company, 20520 Turku, Finland.
- Department of Pathology and Laboratory Medicine, College of Medicine, King Saud University, King Saud University Medical City, Riyadh 11451, Saudi Arabia.
ORCID-Profile: Sarah Almuhayya, Rua Babaier, Eija Säilynoja
Zitieren
APA
Almuhayya, S., Babaier, R., Säilynoja, E., & Somily, A. M. (2026). Effects of Acidic Exposure on Surface Properties and Bacterial Adhesion of Three Resin-Based CAD/CAM Materials. Polymers, 18(15), 1818. https://doi.org/10.3390/polym18151818
Vancouver
Almuhayya S, Babaier R, Säilynoja E, Somily AM. Effects of Acidic Exposure on Surface Properties and Bacterial Adhesion of Three Resin-Based CAD/CAM Materials. Polymers. 2026;18(15):1818. doi:10.3390/polym18151818
BibTeX
@article{Almuhayya2026,
author = {Almuhayya, Sarah and Babaier, Rua and Säilynoja, Eija and Somily, Ali M},
title = {Effects of Acidic Exposure on Surface Properties and Bacterial Adhesion of Three Resin-Based CAD/CAM Materials},
journal = {Polymers},
year = {2026},
volume = {18},
number = {15},
pages = {1818},
doi = {10.3390/polym18151818}
}
EUVIMED