EUVIMEDEUVIMED entdecken
ÜbersichtsarbeitOpen Access · CC BY 4.0

Residual Stresses and Distortion in Material Extrusion Additive Manufacturing of Reinforced Thermoplastic Composites: A Review

Karol Goryl iD, Adrián Vodilka iD, Marek Kočiško iD

Polymers · 23.07.2026 · 18 (15) · 1796

DOI: 10.3390/polym18151796 ↗

Kurz gefasst

Übersichtsarbeit in der Zeitschrift Polymers, online erschienen am 23.07.2026. Verfasst von Karol Goryl und 2 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Manufacturing Technologies, Technical University of Košice, Bayerova 1, 080 01 Prešov, Slovakia. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 170 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Slovak Research and Development Agency, Vedecká grantová agentúra MŠVVaM SR a SAV (VEGA), Ministry of Education, Research, Development, and Youth of the Slovak Republic.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Material extrusion additive manufacturing, commonly implemented as fused deposition modeling (FDM) or fused filament fabrication (FFF), has evolved into a manufacturing route for reinforced thermoplastic composites, including particle-filled, short-fiber-reinforced, and continuous-fiber-reinforced systems. The process is governed by a layer-by-layer thermal cycle. Deposited roads cool rapidly, are repeatedly reheated by subsequent material deposition, and finally cool non-uniformly as part of the growing structure. This thermal history generates residual-stress that may cause warpage, build–platform detachment, delamination, dimensional error, and reduced mechanical performance. This review synthesizes residual-stress formation, measurement, modeling, parameter effects, and mitigation in material-extruded reinforced thermoplastic composites, with emphasis on short and continuous-fiber systems. Stress formation is discussed in terms of constrained thermal contraction, crystallization shrinkage, anisotropic stiffness, fiber-constrained deformation, porosity, and fiber–matrix thermal expansion mismatch. Experimental methods, including hole drilling, layer removal, curvature methods, embedded fiber Bragg gratings, digital image correlation, photoelasticity, and warpage metrology, are critically compared for anisotropic and porous printed composites. Analytical and numerical models are reviewed from layerwise shrinkage formulations to crystallization-coupled thermo-viscoelastic finite element simulations. Finally, mitigation strategies are evaluated. A central conclusion is that reinforcement can suppress visible distortion while increasing stress retained in a stiffer structure. Therefore, warpage alone is not a sufficient residual stress metric.

Schlagwörter

Stichwörter der Autor:innen

annealingcrystallization shrinkagedistortionfiber-reinforced polymersfused filament fabricationmaterial extrusionprocess simulationreinforced thermoplastic compositesresidual stresswarpage

Autor:innen und Institutionen

  • Faculty of Manufacturing Technologies, Technical University of Košice, Bayerova 1, 080 01 Prešov, Slovakia.

ORCID-Profile: Karol Goryl, Adrián Vodilka, Marek Kočiško

Förderung

  • Slovak Research and Development Agency
  • Vedecká grantová agentúra MŠVVaM SR a SAV (VEGA)
  • Ministry of Education, Research, Development, and Youth of the Slovak Republic

Zitieren

APA

Goryl, K., Vodilka, A., & Kočiško, M. (2026). Residual Stresses and Distortion in Material Extrusion Additive Manufacturing of Reinforced Thermoplastic Composites: A Review. Polymers, 18(15), 1796. https://doi.org/10.3390/polym18151796

Vancouver

Goryl K, Vodilka A, Kočiško M. Residual Stresses and Distortion in Material Extrusion Additive Manufacturing of Reinforced Thermoplastic Composites: A Review. Polymers. 2026;18(15):1796. doi:10.3390/polym18151796

BibTeX
@article{Goryl2026,
  author = {Goryl, Karol and Vodilka, Adrián and Kočiško, Marek},
  title = {Residual Stresses and Distortion in Material Extrusion Additive Manufacturing of Reinforced Thermoplastic Composites: A Review},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {15},
  pages = {1796},
  doi = {10.3390/polym18151796}
}
Kostenlos starten →