EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Influence of 3D Printing Parameters on Apparent Resistivity, Repeatability and Time-Dependent Drift of Conductive PLA

Diana Popescu iD, Ștefan Cula iD, Lidia Florentina Parpală iD

Polymers · 22.05.2026 · 18 (11) · 1274

DOI: 10.3390/polym18111274 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 22.05.2026. Verfasst von Diana Popescu und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Robots and Production Systems, National University of Science and Technology POLITEHNICA Bucharest, 060042 Bucharest, Romania. Die Arbeit nennt 34 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Conductive filaments for Material Extrusion Additive Manufacturing (MEX) can enable low-cost fabrication of functional parts with embedded electrical features. However, systematic studies on process-dependent electrical properties like apparent resistivity and repeatability are limited, and the post-printing stability of the electrical response is not commonly addressed. This study evaluates the influence of printing temperature, printing speed and layer height on the apparent resistivity, specimen-to-specimen repeatability and time-dependent drift of a commercial carbon black-filled conductive PLA filament (ProtoPasta). The novelty of the study consists of evaluating not only the initial apparent resistivity, but also the repeatability between specimens and the post-print drift of apparent resistivity over a 0–50 h interval. The filament was investigated using three printing temperatures (210–230 °C), two printing speeds (60–80 mm/s) and three layer heights (0.2–0.4 mm), with three replicates per configuration. Apparent resistivity ranged between 0.156 and 0.205 kΩ·mm at t0 and between 0.162 and 0.222 kΩ·mm at t50. Multifactorial ANOVA and main-effects analyses showed that the printing temperature was the main factor affecting mean apparent resistivity at both t0 and t50. Higher temperature reduced apparent resistivity, most likely due to improved polymer flow, inter-bead/inter-layer bonding and conductive-network continuity. Printing speed had no significant main effect on the mean apparent resistivity or drift within the tested range. Repeatability depended on the parameter configuration and measurement time, with variability increasing after 24 h and then becoming mainly dependent on layer height. Drift analysis showed a significant main effect of layer height and a significant layer height × temperature interaction, with the largest increase at 0.3 mm. These results show that parameter selection for conductive MEX parts should consider both the initial resistivity level and post-print stability over time.

Schlagwörter

Stichwörter der Autor:innen

apparent resistivitycarbon black-filled PLAconductive PLAelectrical driftlayer heightmaterial extrusionprinting temperaturerepeatability

Autor:innen und Institutionen

  • Department of Robots and Production Systems, National University of Science and Technology POLITEHNICA Bucharest, 060042 Bucharest, Romania.

ORCID-Profile: Diana Popescu, Ștefan Cula, Lidia Florentina Parpală

Zitieren

APA

Popescu, D., Cula, Ș., & Parpală, L. F. (2026). Influence of 3D Printing Parameters on Apparent Resistivity, Repeatability and Time-Dependent Drift of Conductive PLA. Polymers, 18(11), 1274. https://doi.org/10.3390/polym18111274

Vancouver

Popescu D, Cula Ș, Parpală LF. Influence of 3D Printing Parameters on Apparent Resistivity, Repeatability and Time-Dependent Drift of Conductive PLA. Polymers. 2026;18(11):1274. doi:10.3390/polym18111274

BibTeX
@article{Popescu2026,
  author = {Popescu, Diana and Cula, Ștefan and Parpală, Lidia Florentina},
  title = {Influence of 3D Printing Parameters on Apparent Resistivity, Repeatability and Time-Dependent Drift of Conductive PLA},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {11},
  pages = {1274},
  doi = {10.3390/polym18111274}
}
Kostenlos starten →