Mechanical Performance of Novel 3D-Printed Symmetric Corrugated Hierarchical Honeycombs
Polymers · 18.05.2026 · 18 (10) · 1233
DOI: 10.3390/polym18101233 ↗Kurz gefasst
Fachartikel in der Zeitschrift Polymers, online erschienen am 18.05.2026. Verfasst von Derui Zhang und 9 weiteren Autor:innen. Beteiligte Einrichtung: School of Mechanical and Automotive Engineering, Liaocheng University, Liaocheng 252000, China. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 51 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: National Natural Science Foundation of China, Shandong Academy of Sciences, collaborative innovation project for the vice president of science and technology.
Abstract (Originalsprache)
Symmetric corrugated hierarchical honeycombs (SCHHs) are critical lightweight load-bearing structures, featuring distinctive topological architectures and excellent mechanical performance. However, they are prone to local buckling under out-of-plane compression and shear loading, which degrades their overall load-bearing capacity. To address this limitation, this work proposes an innovative dual-optimization strategy integrating cylindrical support structure introduction and nano-silica (SiO2) matrix modification to synergistically enhance the compressive and tribological properties of SCHHs. 3D-printed SCHHs and their reinforced variant (SCHH-AC) with embedded cylindrical supports were fabricated, and the effects of nano-SiO2 modification (0–9 wt.%) on the compressive performance and tribological behavior of the photopolymer resin matrix were systematically investigated. Experimental results demonstrate that the SCHH-AC-7% SiO2 configuration achieves optimal compressive performance. A critical SiO2 concentration threshold was identified: agglomeration at 9 wt.% induces severe mechanical degradation. Tribological tests confirm that SiO2 incorporation effectively reduces the resin matrix’s friction coefficient and wear rate, with the 7 wt.% concentration yielding the lowest wear rate. Additionally, geometric parametric analysis reveals that increasing the corrugation period number and amplitude further enhances SCHH’s compressive strength and energy absorption. This study establishes a theoretical and experimental foundation for the structural design and material modification of lightweight honeycombs, advancing their practical application in high-performance engineering fields demanding lightweight load-bearing and wear resistance.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- School of Mechanical and Automotive Engineering, Liaocheng University, Liaocheng 252000, China.
- Shaanxi Special Equipment Inspection and Testing Institute, Xi'an 710048, China.
- School of Materials Science and Engineering, Liaocheng University, Liaocheng 252000, China.
- State Key Laboratory for Strength and Vibration of Mechanical Structures, School of Aerospace Engineering, Xi'an Jiaotong University, Xi'an 710049, China.
ORCID-Profile: Anfu Guo, Yaqin Song, Shaoqing Wang
Förderung
- National Natural Science Foundation of China
- Shandong Academy of Sciences
- collaborative innovation project for the vice president of science and technology
- the Natural Science Foundation of Shandong Province
- the collaborative innovation project for the vice president of science and technology
- the Shandong Province Science and Technology-based Small and Medium-sized Enterprises Innovation Capability Enhancement Project
Zitieren
APA
Zhang, D., Ma, J., Liu, L., Zhu, Y., Guo, A., Qu, P., Guo, S., Song, Z., Song, Y., & Wang, S. (2026). Mechanical Performance of Novel 3D-Printed Symmetric Corrugated Hierarchical Honeycombs. Polymers, 18(10), 1233. https://doi.org/10.3390/polym18101233
Vancouver
Zhang D, Ma J, Liu L, Zhu Y, Guo A, Qu P, et al. Mechanical Performance of Novel 3D-Printed Symmetric Corrugated Hierarchical Honeycombs. Polymers. 2026;18(10):1233. doi:10.3390/polym18101233
BibTeX
@article{Zhang2026,
author = {Zhang, Derui and Ma, Junpeng and Liu, Long and Zhu, Yan and Guo, Anfu and Qu, Peng and Guo, Shuai and Song, Zengrui and Song, Yaqin and Wang, Shaoqing},
title = {Mechanical Performance of Novel 3D-Printed Symmetric Corrugated Hierarchical Honeycombs},
journal = {Polymers},
year = {2026},
volume = {18},
number = {10},
pages = {1233},
doi = {10.3390/polym18101233}
}
EUVIMED