EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comparative Analysis of AWJM Performance in FFF-Printed PLA and PLA–CF: Influence of Process Parameters and Cutting Regions

Pedro F Mayuet Ares iD, Lucía Rodríguez-Parada iD, Sergio de la Rosa iD, Moises Batista iD

Polymers · 15.05.2026 · 18 (10) · 1210

DOI: 10.3390/polym18101210 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Polymers, online erschienen am 15.05.2026. Verfasst von Pedro F Mayuet Ares und 3 weiteren Autor:innen. Beteiligte Einrichtung: Mechanical Engineering and Industrial Design Department, School of Engineering, University of Cadiz, Avda. de la Universidad de Cádiz, 10, E11519 Pue…. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 32 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Spanish Government (SCIENCE AND INNOVATION MINISTRY/FEDER.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additive manufacturing by Fused Filament Fabrication (FFF) enables the fabrication of complex polymer components, although limitations in surface quality and dimensional accuracy often require post-processing. Abrasive water jet machining (AWJM) is a non-thermal technique suitable for improving surface integrity in polymers and composites without inducing thermal damage. This study investigates the AWJM performance on FFF-printed polylactic acid (PLA) and carbon-fiber-reinforced PLA (PLA–CF), focusing on the influence of water pressure (WP), traverse feed rate (TFR), and abrasive mass flow rate (AMFR). A full factorial design was implemented, and surface integrity was evaluated through surface roughness (Ra) and kerf taper (T), considering their variation across characteristic cutting regions: initial damage region (IDR), smooth cutting region (SCR), and rough cutting region (RCR). Results show that WP and TFR are the dominant parameters, while AMFR has a limited effect within the studied range. The SCR exhibits the lowest roughness, whereas the RCR shows significant degradation due to energy loss. Both materials present similar behavior, with only minor improvements in PLA–CF. ANOVA confirms that process parameters have a stronger influence than material type, providing useful criteria for AWJM optimization in FFF polymers.

Schlagwörter

Stichwörter der Autor:innen

abrasive water jet machiningfused filament fabricationpolylactic acidprocess parameterssurface integrity

Autor:innen und Institutionen

  • Mechanical Engineering and Industrial Design Department, School of Engineering, University of Cadiz, Avda. de la Universidad de Cádiz, 10, E11519 Puerto Real, Spain.

ORCID-Profile: Pedro F Mayuet Ares, Lucía Rodríguez-Parada, Sergio de la Rosa, Moises Batista

Förderung

  • Spanish Government (SCIENCE AND INNOVATION MINISTRY/FEDER

Zitieren

APA

Mayuet Ares, P. F., Rodríguez-Parada, L., de la Rosa, S., & Batista, M. (2026). Comparative Analysis of AWJM Performance in FFF-Printed PLA and PLA–CF: Influence of Process Parameters and Cutting Regions. Polymers, 18(10), 1210. https://doi.org/10.3390/polym18101210

Vancouver

Mayuet Ares PF, Rodríguez-Parada L, de la Rosa S, Batista M. Comparative Analysis of AWJM Performance in FFF-Printed PLA and PLA–CF: Influence of Process Parameters and Cutting Regions. Polymers. 2026;18(10):1210. doi:10.3390/polym18101210

BibTeX
@article{MayuetAres2026,
  author = {Mayuet Ares, Pedro F and Rodríguez-Parada, Lucía and de la Rosa, Sergio and Batista, Moises},
  title = {Comparative Analysis of AWJM Performance in FFF-Printed PLA and PLA–CF: Influence of Process Parameters and Cutting Regions},
  journal = {Polymers},
  year = {2026},
  volume = {18},
  number = {10},
  pages = {1210},
  doi = {10.3390/polym18101210}
}
Kostenlos starten →